Cementitious Scratch / Key Coat
Spatter Dash SB cement-based key coat composed of hydraulic binders, selected sand aggregates, and high-performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily spray-able mortar. Spatter Dash SB is a high-quality product for multipurpose applications and contains a special bonding agent.
Spatter Dash SB is supplied in 50Kg Bag.
Yield - 1.3-1.6Kg/m2/mm thickness.
Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.
The original sealed bag of Spatter Dash SB has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place, at temperatures between 5ºC - 35ºC.
Mixing
Add to the mixing container 11.5-14.0 liters of water for each 50Kg bag of Spatter Dash SB. Add the powder to the water and mix with a mechanical plaster mixer or low-speed electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency.
Blend Spatter Dash SB manually for small quantities and maintain the correct amount of powder to water. Mix for approximately 1-2 minutes until achieving a homogeneous mix.
Application
Preferably, apply Spatter Dash SB in a single coat application to achieve the desired rough thickness of 4-6 mm. Apply mixed material using a mechanical spray or manual spatter machine or hawk & trowel technique. Cover 95-100% of surface area that will be plastered.
Allow the installed Spatter Dash SB to remain undisturbed for at least 48 hours.
Curing
Cure Spatter Dash SB by spraying the applied material surface with water every 12hrs for a minimum of 3 days. During hot & dry conditions, allow curing for a minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.
Cleaning
Clean all tools immediately after finishing with water. Clean hardened materials mechanically.
The substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, or any other substance that might impair the substrate's quality bonding.
Before Spatter Dash SB Application, damp the entire surfaces with clean potable water. The substrate should be neutralized surface at the time of Spatter Dash SB application.
Ensure the substrate is suitable for the application of Spatter Dash SB; in case of doubt, try on the sample area to assess its suitability.
Do not apply the product under direct rain, extreme wind, and temperatures below +5ºC or above +45ºC.
Spatter Dash SB is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Spatter Dash SB is non-flammable.
For further information, please refer to the material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High-quality lightweight premixed acoustic plaster
Premixed cementitious masonry grout
Sprayable lightweight premixed plaster
High-quality gypsum plaster
Light weight gypsum perlite plaster
Premixed 8 to 20mm thick polymer modified cementitious self leveling underlayment.