Flooring & Coatings Systems
Vetotop ED910

High strength decorative epoxy floor and wall coating

Decorative floors and walls in residential, commercial and industrial structures
Shopping malls, showrooms, home interiors, garages
Large variety of effects such as antique, stained, chip impreginated, etc.
Fast Download
Technical Data Sheet
download (*.pdf 0.31Mb)
Saveto Flooring Technical Guide
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop ED910 is part of Saveto’s decorative epoxies product range that contains top of the line products that has a decorative as well as a protective function. Vetotop ED910 is a two component 100% solids epoxy based coating that is applied at a thickness of 500 microns with the possible use of floor chips and other application techniques to provide a large variety of decorative effects. The product has excellent physical properties that makes it abrasion and chemical resistant while being waterproof.

  • Dual decorative as well as protective function
  • Large variety of decorative effects
  • Excellent abrasion and chemical resistance
  • Reduces water and chloride intrusion
  • Easily cleanable
  • High bond strength, stronger than concrete cohesive strength
Compiliance Standard

BS EN476:2009 as class 1 in flame spread.

Packaging & Coverage

Vetotop ED910 supplied in 15 Liter Kit. Yield - 15 m²/kit @ 1mm thickness

Vetoprime EP491 supplied in 4 Liter Kits. Yield - 7-10 m2/ Liter.

Shelf Life & Storage

Original sealed bag of Vetotop ED901 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Design Criteria

Vetotop ED910 is designed to be a hard wearing two coat application on cementitious or metal substrates. When used on metal substrates, use Vetoprime EP290 which contains corrosion inhibitors. The applied product will be resistant to water as well as a wide range of chemicals.


The substrate is to be primed by Vetoprime EP491prior to the application of Vetotop ED910. Vetoprime EP491 should be mixed in the proportions supplied. Add the entire contents of the hardener can to the base can. When thoroughly mixed, preferably using a slow speed mixer, the primer should be applied in a thin, continuous film using rollers or stiff brushes. Work the primer well into the surface of the concrete taking care to avoid ponding or over application. The primer should be left to achieve a tack-free condition before applying the top coat.


Since decorative finish is highly dependant on workmanship, Vetotop ED910 is to be mixed and applied by professional certified applicators. Please contact saveto local representative for recomendation on certified applicator for the decorative range.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well profiled surface. All necessary repairs should be made prior to application by using epoxy mortar from Vetorep ER range.

New concrete floors shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Additional Information
Health & Sefety

Vetotop ED910 and Vetoprime EP491 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

Vetotop EC493

Solvent based high performance, self priming, thin epoxy topping

view more
Featured Product
Vetorel XT429

Powder release agent for decorative and stamped concrete.

Releasing of stamping and imprinting tools from concrete surfaces.
Act as a secondary colorant and antique effect producion of imprinted concrete.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com