Cementitious based adhesive and base coat for EIFS / ETICS
Vetotherm Flex is a polymer modified deformable cementitious adhesive specially designed for permanent fixing of thermal insulation boards to a wide range of substrates, including concrete and masonry. Vetotherm Flex is also designed for use as a protective mortar providing a durable layer for insulation boards suitable for several types of decorative finishes.
Vetotherm Flex supplied in 25kg Bag.
Coverage - 1.3 - 1.5 Kg/m2 / mm Thickness
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.
Original sealed bags of Vetotherm Flex have a shelf life of 12 months, provided to store clear ground in a dry, shaded place below 23ºC.
Priming
Apply Vetotherm Flex directly on concrete, cement plaster, and masonry. In the case of very porous substrates, spray water onto the surface before the application.
Mixing
To ensure proper mixing, use a mechanically powered mixer or heavy-duty drill fitted with a suitable paddle.
Add 6.75 - 7.5 Liter (for each 25 kg bags) of clean water to a clean container. Add the powder slowly to the water while mixing continuously with a low-speed mixer/ heavy-duty drill (400 - 600 rpm) fitted with a suitable mixing paddle. Continue mixing for 3 minutes until obtaining a uniform consistency.
Leave the mixture for 5 - 10 minutes to mature, then remix without adding additional water.
Application
As an Adhesive
Apply the mortar in a strip around the insulation board with enough spots to ensure full coverage. In the case of a smooth or plastered substrate, employ the back buttering technique. Use a notched trowel to spread the mortar on the back of the insulation board.
As a Base Coat and Protective Layer
Apply the mortar over the fixed thermal insulation panels. Using an aluminum roll, embed the precut reinforcing mesh onto the freshly applied mortar until it is fully immersed in the Vetotherm Flex layer.
Smoothen the surface with a long flat trowel. Apply more than one Vetotherm Flex layer where it is needed. A double or triple reinforcement mesh can be used.
Note:
Mesh strips have to be overlapped by approximately 10 cm.
This material is a thin bed adhesive and can not be applied for more than 10mm thickness.
Cleaning
Clean all tools immediately after finishing with water. Clean hardened materials mechanically.
All surfaces must be clean and free from oil, grease, or loose materials. The insulation board has to be fixed firmly by using Vetotherm adhesives and anchors.
Fill the large gaps between insulation boards with strips of insulation board to leave minimal gaps, or fill with PU foam of similar U-Value to the insulation boards.
Protect all the buildings by using PVC Vetotherm accessories unless otherwise is specified.
Mesh strips have to be overlapped by approximately 10 cm.
This material is a thin bed adhesive and can not be applied for more than 10mm thickness.
Vetotherm Flex is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Wash any skin contact with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetotherm Flex is non-flammable.
For further information, please refer to the material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Advanced modified cementitious thermal insulating plaster
Advanced modified cementitious lightweight, thermal insulating masonry mortar
Cementitious based adhesive and base coat for EIFS / ETICS
Advanced Modified Cementitious Thermal Insulating Plaster
Prefabricated decorative thermal insulating expanded coated polystyrene
Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 3 mm