Water resistant high quality cementitious premixed putty
Vetonit Putty WR is composed of white cement, fine fillers, bonding chemicals, and high-performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site. It only requires the addition of clean water to produce a cohesive mix. Vetonit Putty WR is a high-quality product applied as a thin underlayment to repair undulations. It provides a very smooth surface finish that is ideal for subsequent application of paint and decorative coatings. Vetonit Putty WR can be applied generally in thickness from 1mm to 3mm.
Vetonit Putty WR is supplied in 20kg Bags.
Consumption: 1.0 - 1.2 Kg/m2/1mm Thickness
Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.
The original sealed bags of Vetonit Putty WR have a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 25ºC.
Mixing
For mechanical mixing, add to the mixing container 7.6-8.8 liters of water for each 20kg bag of Vetonit Putty WR. Add the powder to the water and mix with a mechanical plaster mixer or a low-speed electric drill fitted with a suitable paddle. Mix for 3-4 minutes until achieving a uniform, lump-free consistency.
Leave the mixed material to stand for 10 min and briefly remix without adding water.
Mix small batch quantities manually for approximately 1-2 min, or until achieving a when a homogenous mix.
When required, add 1 liter of Vetonit Bond 2 to the mixing water and adjust the water requirement for each 20kg bag of Vetonit Putty WR accordingly. Follow the same mixing procedure as above.
Use the mixed material within 3 hours. Do not add water once the mixed filler mortar starts to stiffen or harden.
Application
Generally, apply Vetonit Putty WR is in single or double coats.
Apply Vetonit Putty WR to the substrate by pressing the putty firmly onto it. Use a flat trowel to level the material to a smooth finish.
Apply a second coat if necessary once the first coat initially sets.
After applying Vetonit Putty WR, it is recommended to apply one coat of alkali-resistant primer followed by two coats of acrylic emulsion paint or other suitable coatings.
Curing
Vetonit Putty WR is self-curing, and it does not require water treatment. However, when using Vetonit Putty WR as a final finish, it is recommended to apply a single Bond Pure coat. The bonding agent will perform as a surface enhancer and a curing compound that will naturally disintegrate with time.
Cleaning
Clean all tools immediately after finishing by water. Clean the hardened materials mechanically.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Before the Vetonit Putty WR application, wet the entire surfaces with clean potable water. The surface should look damp at the time of the Vetonit Putty WR application.
Vetonit Putty WR is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during the application. Wash any skin contact with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetonit Putty WR is non-flammable.
For further information, please refer to the material safety data sheet.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
PVA copolymer based high-quality putty
Gypsum surfaces skim and finish compound
High quality premixed surface crack filler
Water resistant internal use premix smooth cement coating
Water-resistant external use premix smooth cement coating
Multipurpose low viscosity bonding agent & admixture