Saudi Arabia
Bahrain Egypt Jordan Qatar UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Wall & Facade Systems
Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Uses
Expanded and extruded polystyrene and rock wool adhesive on cementitious substrates, masonry and gypsum boards.
Fiber mesh reinforced base coat as part of EIFS / ETICS systems.
Ready to receive a wide range of decorative finishes.
Fast Download
Technical Data Sheet
download (*.pdf 0.20Mb)
Method of Statement
download (*.pdf 0.69Mb)
Catalogues
Decorative Coating Brochure
download (*.pdf 2.78Mb)
External Thermal Insulation Composite System - ETICS
download (*.pdf 8.19Mb)
Technical Information
Product Description

Vetotherm Ultra is a polymer modified deformable cementitious adhesive specially designed to be used for permanent fixing of thermal insulation boards to a wide range of substrates including concrete, and masonry. Vetotherm Ultra is also designed for use as a protective mortar providing a durable layer for insulation boards that is suitable to receive several types of decorative finishes.

Advantages
  • Single component easy to apply.
  • Water resistant.
  • Thixotropic, non-sag.
  • High physical and mechanical properties.
  • Deformable and impact resistant.
  • Requires no primer.
  • Specifically designed for rockwool and glasswool panels.
  • High flexebility
Compiliance Standard
  • ETAG 004 requirements for ETICS / EIFS systems.
  • ANSI/EIMA requirements for ETICS / EIFS systems.
  • ISO 13007:2010 as C2TE S2
  • EN12004:2010 as C2TE S2
Packaging & Coverage

Vetotherm Ultra supplied in 25 Kg Bag
Coverage - 1.3 - 1.5 Kg /m2 / mm Thickness

Shelf Life & Storage

Original sealed bags of Vetotherm Ultra has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
Grey
Application Information
Instructions for use

Priming

Vetotherm Ultra can be applied directly on concrete, cement plaster and masonry. In case of very porous substrates, water should be sprayed onto surface prior to the application.

Mixing

To ensure proper mixing, a mechanically powered mixer or heavy duty drill fitted with suitable paddle should be used. Add 9 - 9.75 liters (for each 25 kg bags) of clean water to a clean container. The powder is then added slowly to the water while mixing continuously with low speed mixer/ heavy duty drill (400 - 600 rpm) fitted with a suitable mixing paddle.

Mixing time should be continued for 3 minutes until a uniform consistency is obtained.

Application


As an Adhesive:
Apply the mortar in a strip around the insulation board with a few spots in the middle. In case of a smooth or plastered substrate, back buttering technique can be employed and a notched trowel can be used to spread the mortar on the back of the insulation board.

As a Base Coat and Protective Layer:
Apply the mortar over the fixed thermal insulation panels. Using an aluminum roll, embed the precut reinforcing mesh onto the fresh applied mortar until its fully immersed in the Vetotherm Ultra layer.
Smoothen the surface with a long flat trowel. More than one Vetotherm Ultra layer can be applied and where needed double or triple reinforcement mesh can be used.


Note: Mesh strips have to be over lapped by approximately 10 cm.

Cleaning
All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

All surfaces must be clean and free from oil, grease or loose materials. The insulation board has to be firmly fixed using Vetotherm adhesives and anchors. Large gaps between insulation boards must be filled with strips of insulation board to leave minimal gaps or filled with PU foam of similar U-Value to the insulation boards. All edges of the building need to be protected by PVC Vetotherm accessories unless otherwise specified.

Additional Information
Health & Sefety

Vetotherm Ultra is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise. Vetotherm Ultra is non-flammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Cool Mortar

Advanced modified cementitious light weight, thermal insulating masonry mortar 

 

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetotouch EUROPA

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5 mm

view more
Featured Product
Vetorep CR520

(Formerly known as Vetomortar CHR)

High strength structural repair mortar

Uses
Repair of broken structural concrete elements
Vertical concrete repair up to 75 mm in a single layer
Overhead concrete repair up to 50 mm in a single layer
Horizontal and patch repairs up to 100 mm in a single layer
Honeycomb repairs, general concrete repairs
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.