Exterior decorative textured render
Vetotouch Tyrolean is a cement-based decorative finish composed of hydraulic binders, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar.
- Factory controlled pre-blend ensures consistently high quality.
- Requires only the addition of water on-site at the time of usage.
- Provides textured and stenciled finishes.
- Improved workability and curing
- Easy application with uniform work flow enables high productivity and superior finishing.
- Strong adhesion on a variety of substrates.
- Internal and external applications.
- Weather-resistant.
- UV stable pigment provides resistance to fading and eliminates the need for additional paint.
- Suitable for humid and dry conditions.
- EN 998:2010
- EN 926:2011
- EN 13914:2005
- EN 1015:2000
Vetotouch Tyrolean is supplied in a 25kg Bag.
Coverage : 1.5kg/m2/mm Thickness.
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, consistency used, method of application, and wastage.
The original sealed bag of Vetotouch Tyrolean has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.
Mixing
Add to the mixing container 7-8 liters of water for each 25kg bag of Vetotouch Tyrolean. Add the powder to the water and mix with a mechanical plaster mixer or low-speed heavy-duty electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency. Leave the mixed material to stand for 10min and briefly remix without adding water.
For small batch quantities, mix the product manually for approx. 1-2 min or when achieving a homogeneous. Add 0.5 to 1.0 liter of Vetobond AB432 to the mixing water and adjust the water requirement accordingly for each 25kg bag. Follow the same mixing procedure as described above.
Use the mixed material within 30-60 minutes.
Do not add water once the mixed mortar starts to harden.
Application
Apply Vetotouch Tyrolean in one or two layers up to 6mm/coat. Apply by hopper Gun or by Terol hand-operated machine.
To protect Vetotouch Tyrolean, apply Vetoseal XX772 by brush or spray machine after three days of curing.
Curing
Cure Vetotouch Tyrolean by spraying an acrylic based curing compound on the surfaces of the applied materials.
Cleaning
Clean tools with water before the mortar hardens. After the hardening, remove its residuals mechanically only.
The substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Before the Vetotouch Tyrolean application, wet the entire surfaces with clean potable water. The surface should look damp at the time of the Vetotouch Tyrolean application.
Vetotouch Tyrolean is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetotouch Tyrolean is non-flammable.
For further information, please refer to the product material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 5mm
Grooved decorative finish coat
UV resistant pigmented premixed textured plaster
Marble chip decorative exterior and interior finishing system
Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 3mm
Glass fiber reinforcement meshes designed for use with external thermal insulation coating systems.
