Advanced Modified Cementitious Thermal Insulating Plaster
Vetotherm Plaster is a blend of OPC, silica sand, and graded lightweight aggregates plus functional additives for enhancing Workability and adhesion. It can be applied on all surfaces after the proper preparation of the surface. The product provides thermal insulation for building wall sections relying on advanced material technologies.
Excellent thermal insulation properties.
Fast mixing application using a spray machine.
It contains a special additive that reduces friction and prolongs the lifespan of the equipment.
Factory controlled pre-blend ensures consistently high quality.
Uniform color/mass.
Improved workability & curing.
Easy application with uniform work flow enables high productivity & superior finishing.
Strong adhesion on a variety of substrates.
Internal & external applications.
Shrinkage control reduces surface cracks.
Suitable for humid & dry conditions.
BS:EN 998-1 CSIII, W1, T1
Cement type: ASTM C150, type1.
Vetotherm Plaster is supplied in 20Kg Bag, Coverage ≈ 32 lit wet/20 kg dry bag.
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.
An original sealed bag of Vetotherm Plaster has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 25ºC.
Mixing
For manual application, add to the mixing container 6.6 - 7.4 liters of water for each 20 Kg bag of Vetotherm Plaster or 33 - 37% of the machine application weight. Add the powder to the water and mix with a mechanical plaster mixer or low-speed electric drill fitted with a suitable paddle for 3-4 minutes, until achieving a uniform, lump-free consistency.
Manual mixing is allowed for small batch quantities. Mix for approximately 1-2 minutes, until achieving a homogeneous mix.
Application
Apply Vetotherm Plaster in a single or two coats on rough or smooth surfaces by manual or machine application to achieve the desired thickness of 25-100 mm.
Apply the mixed material using a spray machine or hawk & trowel technique. Rod or screed to uniform thickness, not exceeding 25 mm for a single coat or 25 mm for each coat for multiple layers. Pres the first layer hard against the surface.
For the second layer, allow the first layer to set (60-120min depending on weather) partially. Apply the second layer as described above.
Water spray the surface if the second layer is carried out the next day.
Curing
The best way to cure Vetotherm Plaster is by spraying water evenly on the applied material surfaces every 12 hrs for a minimum of 3 days. During hot & dry conditions, allow curing for a minimum of 5 days; It will help to obtain high mechanical strengths.
Cleaning
Clean all tools immediately after finishing with water. Hardened materials can be cleaned mechanically.
The substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Before Vetotherm Plaster, wet the entire surface with clean potable water; the surface should look damp at the time of the Vetotherm Plaster application.
- Do not mix with any additives or products unless recommended by Saveto.
- Make sure the substrate is suitable for plaster application. In case of doubt, try on a sample area to assess its suitability.
- Do not apply the product at a temperature less than +5ºC. During the summer season, the working area must be covered to prevent ill-effects from direct sun and excessive air-draught during the initial curing stage.
Vetotherm Plaster is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eye irritation, immediately wash with a copious amount of cold water. Seek medical advice.
For further information, please refer to the material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Advanced modified cementitious thermal insulating plaster
Advanced modified cementitious lightweight, thermal insulating masonry mortar
Cementitious based adhesive and base coat for EIFS / ETICS
Cementitious based adhesive and base coat for EIFS / ETICS
Glass fiber reinforcement meshes designed for use with external thermal insulation coating systems.
Low viscosity epoxy grout & injection resin