Primers and Ancillary
Vetotherm E1 System Accessories

Vetotherm AFA ,  Vetotherm ACP & Vetotherm ABP

Uses
Facade anchors are used for fixing Vetotherm EPS (thermal insulation boards) on concrete and light aerated concrete, solid and hollow concrete applicationsand on bricks
Corner Profile reinforcement of window or door corners, edges and jambs
Base Profiles are perfect structural and visual finish and closure of the system
Fast Download
Technical Data Sheet
download (*.pdf 0.91Mb)
Technical Information
Product Description

Vetotherm AFA (Facade Anchors)
A facade anchor (dowel) with plastic nail for additional mechanical strengthening of the thermal insulation system with slabs of EPS and XPS.

Vetotherm ACP( Corner Profile with Mesh)
Angular plastic profile with integrated alkali-resistant mesh is used to more easily and properly forming 90-degree angles and for reinforcing all window or door corners, edges and jambs in the contact insulation system – ETICS.

Vetotherm ABP (Base Profile LU)
Base profile without a drip ledge is used for ending/closing up insulating material at its sides or for closing the system in its top part. This profile cannot be used in situations where the rainwater drain- age from the system must be ensured.

Advantages
  • Mechanical strengthening of the thermal insulation system- ETICS by using anchors
  • Base Profiles protects the system against mechanical damage
  • Corner profile protects the corners against mechanical damage, prevents hairline cracking, creates an ideally straight corner
  • Corner profile is without exposed edge – used under plaster
Compiliance Standard

ETAG 004 requirements for ETICS / EIFS systems.

Packaging & Coverage

Vetotherm AFA 8 x115, is supplied in 200pcs carton
                       8 x155, is supplied in  200pcs carton

Vetotherm ABP  53/1, is supplied in 50m @50mm EPS thickness

                       103/1, is supplied in 50m @100mm EPS thickness

Vetotherm ACP, is supplied in 125m / carton @ 80x80mm mesh thickness

Application Information
Instructions for use

Anchoring
Start anchoring Vetotherm EPS boards minimum 48 hours after sticking the boards in order to allow the adhesive to dry completely. Vetotherm AFA (anchors) should be mounted according to a diagram depending on the height of the building, the region and the strength of the wind (refer to Saveto ETICS guide).
If Vetotherm EPS have a thickness exceeding 8 cm, you need to make previously a hole of 2 cm depth with a cutter and then, in this hole, to drill an opening for the screw anchor. After the mounting of the dowels, the hole should be filled with a polystyrene cap.
After the completion of the anchoring, cover the heads of the dowels with Saveto Vetotherm Flex to flush with the level of the boards.

Reinforcement of the loaded areas
Apply ready to use angle Vetotherm ACP (Corner Profile) to reinforce external angles, and apply Vetotherm ABP(Base Profile) to close up insulating material at its sides or to close the system in its top part . Apply Saveto Vetothem Flex along the edge, place the profile and press it tightly.
Corners around doors and windows should be strengthened by applying adhesive on the base, then place on the adhesive pieces of fibreglass mesh with minimum dimensions of 20х50 cm. Apply more adhesive to cover the mesh completely.
Before continuing to reinforce the entire surface, wait 24 hours to allow these areas to dry.

Additional Information
Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond

Multi-purpose bonding agent & admixture

Saveto PP Fiber

High Quality Monofilament Polypropylene Fibers

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Premix Plaster SF

Fiber reinforced sprayable premixed plaster

Uses
Internal & external plaster on block walls and rough surfaces
Plastering on fairfaced concrete and precast panels subsequent to Spatter Dash SB scratch coat
Plastering to a thickness of 25 mm on vertical surfaces and ten mm on overhead surfaces
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map