Primers and Ancillary
Vetoprime UP360

Penetrating Moisture Cure Poly-urethane Primer

Uses
Penetrating primer for interior and exterior floor coatings
As a dust proofer for cementitious surfaces.
Sealing of semi-porous cementitious substrates.
Priming of joint edges to receive urethane, epoxy, and polyurea based sealants.
Priming of concrete slabs and walls to receive solvent free epoxy, urethane, MMA, polyurea and hybrid coatings.
Priming of concrete substrates to receive epoxy and urethane based repair mortars.
Priming of cementitious screeds to receive epoxy, urethane and resinous toppings.
Fast Download
Technical Data Sheet
download (*.pdf 0.13Mb)
Method of Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetoprime UP360 is a penetrating primer for  Vetotop product range, its applied on prepared concrete and cementitious substrates to seal the substrate and enhance bonding with top coats. The product can be used as a stand alone product in internal applications as a seal coat to harden cementitious surfaces and prevent dusting. Vetoprime UP360 is a single component solvent based, moisture cure polyurethane resin that has penetrating properties making it ideal for concrete substrates.

Advantages
  • Easily applied by brush, roller.
  • Versatile with applications in a large number of coating materials and sealants.
  • Deep penetration, designed for semi porous surfaces.
  • Large application temperature range (3 to 500C)
  • High wetting properties.
  • Cost effective, suitable for use in MENA region conditions.
Packaging & Coverage

Vetoprime UP360 is supplied in 10 Liters, Coverage: 100-150 m2 / 10 ltr

Shelf Life & Storage

Original sealed container of Vetoprime UP360 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.

Colors
Dark brown
Application Information
Instructions for use

Priming
Mix Vetoprime UP360 as supplied. Vetoprime UP360 shall be applied in a thin continuous film using stiff brushes or rollers. Avoid over-application and puddles.
Vetoprime UP360 shall be allowed to become tack-free prior to the application of the top coat but well within the open time specified for the given temperature.
The hotter the substrate, the more quickly the primer will become dry.

Curing

At temperatures below 20ºC, the cure rate will be slower. Conversely, at temperatures above 20ºC, the cure rate will be faster. The RH must be in the range of 25-90%. The lower the RH the slower cure rate.

Cleaning
All tools and equipment shall be cleaned immediately after use with Vetonit Solvent XX400.

Surface Preparation

It is essential that Vetoprime UP360 is applied to a sound, clean and dry surface in order to achieve maximum bond strength between substrate and coating/repair products.

Concrete Substrates
Should be at least 28 days old and relative humidity of the concrete is 75% or below. Laitence deposits on new concrete are best removed by light grit blasting, mechanical scabbling or grinding.
Where heavy contamination by oil and grease has occurred or existing coatings are present, it is essential that all contaminations are removed.

Additional Information
Health & Sefety

Gloves and a barrier cream shall be used when handling these products. If contact with the resin occurs, it must be removed, before if hardens, with resin removing cream follow by washing with soap and water. Do not use solvent.
During use, avoid inhalation of solvent and contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. In case of contact with eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.
Vetoprime UP360 is flammable, Ensure adequate ventilation. Do not smoke or use near naked flame.
Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond

Multi-purpose bonding agent & admixture

Saveto PP Fiber

High Quality Monofilament Polypropylene Fibers

Vetobond PB436

Polymeric soil stabilizer

Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Vetotherm EPS

Expanded Polystyrene Sheet

Uses
Expanded polystyrene used as thermal insulation in EIFS / ETICS systems of residential and industrial concrete buildings.
Save energy consumption related to heating and cooling.
Internally or externally in wet & dry conditions, isolates the building from external weather.
Work as a shock and sound absorber.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com

Saveto Company Name