Polymer modified water-resistant adhesive for fixing pool, fountain & water tank tiles.
Vetoset CA547 is a cementitious mortar adhesive composed of hydraulic binders, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar. Vetoset CA547 is suitable for dry-set fixing mortar, particularly for pool, fountain & water tank ceramic wall & floor tiles. Vetoset CA547 is applied in thickness from 3mm to 10mm, depending upon the substrate's type of tiles and quality.
Factory controlled pre-blend ensures consistently high quality.
Requires only the addition of water on-site at the time of usage.
Superior bond in wet & immersed water conditions.
Easy tile installation that enables high productivity.
Superior workability.
Excellent Adhesion on a variety of tiles available in the local market.
Suitable for internal & external applications.
Suitable for dry & wet conditions.
Suitable for horizontal & vertical surfaces.
BS:EN 12004 as C2TE S1
ISO 13007
Vetoset CA547 is supplied in 20Kg bags.
Coverage: 4.0 – 5.5 m²/20Kg bag @ 3mm notched trowel
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastages.
The original sealed bag of Vetoset CA547 has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.
Mixing
For the preparation of mortar adhesive, pour into a container 5.4 - 6.4 liters of water for each 20Kg bag of Vetoset CA547. Add the powder to the water and mix with a low-speed electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency. Allow the mixed material to stand for about 10 minutes and briefly remix without adding extra water.
Blend Vetoset CA547 manually for small quantities and maintain the correct amount of powder to water.
If required, add 0.5 Ltr of Saveto Bond 2 to the mixing water, followed by powder's addition. Use the mixed material within 2 hours.
Do not add water to the mixture once the mortar adhesive starts to harden.
Application
Spread the mixed Vetoset CA547 mortar adhesive and firmly press it onto the surface that will be tiled; work with a notched trowel. Spread the mortar adhesive to an area that can be tiled within 10 -15 minutes.
Place the tiles onto the fresh adhesive mortar and firmly press them with a slight twist; immediately knock them into the desired position. Adjust the position of the tiles, if required, within its adjustability time of 10-15 minutes after installation.
Mortar adhesive must not rise between the tile joints higher than halfway the thickness of the tiles.
Allow the installed tiles to remain undisturbed for at least 48 hours.
It is recommended to use Vetofill CG552 for filling the joint gaps after 2 days of tile installation.
Cleaning
Clean tools and equipment with water immediately after use. Remove the hardened material using mechanical means.
The surface should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, etc.
Wet all surfaces with clean water before the application of Vetoset CA547. The surface should appear damp with no water pooling.
Vetoset CA547 is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetoset CA547 is non-flammable.
For further information, please refer to the material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather resistant cementitious adhesive for ceramic tiles.
Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles
Water-resistant grout for swimming pool tile joints
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
High performance, aromatic & flexible waterproof polyurethane flooring membrane