Renders & Finishes
Saveto Putty Fine

PVA copolymer based high-quality putty

Uses
Use for leveling of minor surface undulations.
Apply internally in dry conditions onto the walls & ceilings.
Use on concrete, plastered surfaces that are smooth, precast concrete surfaces, and on wood.
Suitable for use over plastered surfaces with Saveto products, gypsum boards, and wood surfaces.
Suitable for use over Vetonit Putty WR.
Fast Download
Technical Information
Product Description

Saveto Putty Fine is a water-based putty. It is supplied as a wet putty in pre-weighed pails or bags ready to use on-site. Saveto Putty Fine is a high-quality product that is used as a thin underlayment to repair undulations. It provides a very smooth surface finish that is ideal for subsequent application of paint & decorative coatings. Generally, Saveto Putty Fine can be applied in thicknesses less than 0.7mm.

Advantages
  • Ready to use and easy to apply.
  • It gives a smooth finish by using a putty flat trowel.
  • Excellent filling property.
  • High adhesion to the substrate.
  • Toughness increases with time.
  • Very low VOC.
  • Sandable.
Packaging & Coverage

Saveto Putty Fine is supplied in 20kg plastic pails.

Coverage:60 - 120 m2 /20kg depends on the substrate.

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

 

 

 

Shelf Life & Storage

The original sealed container of Saveto Putty Fine has a shelf life of 18 months, provided it is stored clear of ground in a dry, shaded place between 5 ºC up to 35ºC.

Colors
Pale Creamy
Application Information
Instructions for use

Application

Generally, apply Saveto Putty Fine in single or double coats.

Apply Saveto Putty Fine to the substrate by pressing the putty firmly. Use a flat trowel to work the mixed material to a smooth level.

Once the first coat dries, apply a second coat as necessary.

After applying Saveto Putty Fine, it is recommended to apply one coat of alkali-resistant primer followed by two coats of acrylic emulsion paint or other suitable coatings.

Curing

Saveto Putty Fine is self-curing and does not require water treatment.

Cleaning

Clean all tools immediately after finishing with water. As for the hardened materials, clean them mechanically.

 

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

For previously painted surfaces, remove the old paint before the application of Saveto Putty Fine.

Allow wet surfaces to dry completely before the putty application.

Additional Information
Health & Sefety

Avoid Saveto Putty Fine direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Saveto Putty Fine is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetogyps Compound
Gypsum surfaces skim and finish compound

">

Gypsum surfaces skim and finish compound

Vetonit Crack Filler

High quality premixed surface crack filler

Vetonit Finish WR

Water resistant internal use premix smooth cement coating

Vetonit Finish WR EG

Water-resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

view more
Featured Product
Vetoflex PS782

Two-component polysulphide trafficable joint sealant
(Formerly known as Saveto PS2)

Uses
Heavy duty civil sealant used for sealing joints in: bridges, roadways, concrete ponds, warehouse floors, dams, canals & culvert.
As a general elastic adhesive for materials with dissimilar properties and thermal expansion coefficients.
Movement and static joint sealing in various construction industry requirements.
Suitable for use in contact with sewage water.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com