Elastomeric crack-bridging cementitious waterproof membrane
Vetoproof S is a two component flexible polymer modified cementitious waterproof coating, it has unique crack bridging characteristics even after long term water immersion. The product is suitable for use in contact with potable water and can withstand negative hydrostatic pressure.
Non-Toxic - approved in contact with drinking water.
Flexible, crack bridging material.
Waterproof.
Ready to receive Saveto tile adhesives.
Withstands hydrostatic pressures.
Easy application by brush or roller
Bonds to green or damp concrete.
Effective barrier to sulphates and chlorides.
Excellent bond to concrete and masonry.
Vetoproof S is supplied in 20kg Kit, coverage: 1.0 - 1.8 kg /m2/ Coat
Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, consistency used, method of application and wastage.
Original sealed container of Vetoproof S and has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 35ºC.
Pre-wetting of the substrate
Thoroughly dampen the substrate surface with water using a brush, roller, or spray bottle. High porosity substrates will require more dampening than dense substrates. Do not apply the coating when the substrate is wet, but allow the water to soak in until the substrate is just visibly damp prior to proceeding. Any excess water should be removed using a sponge.
Mixing
Vetoproof S liquid concentrate should be shacked and completely poured from the plastic container into a suitably sized mixing container. Commence mixing with a propeller agitator attached to a slow speed drill (300-500 rpm). The powder component should be added gradually to the liquid to avoid lump formation and mixed for 2 to 4 minutes. Vetoproof S should be immediately used after mixing to avoid settlement of sand. Part mixing is not allowed. Mix whole kits. Do not mix more material than can be used within the pot life. Keep mixing Vetoproof S during the application.
Brush application
The most suitable type of brush is a soft bristled wallpaper paste brush (220mm wide and 50mm deep). Where larger areas are to be applied it is advisable to use a brush with a handle. Load the brush up well and spread the material to the required thickness. If the brush begins to drag during application, do not add water to the material, but dampen the surface again. Finish in one direction for a neat appearance.
Roller application
Application by roller has the benefit of speed over brush application, particularly on smooth substrates. A good quality medium hair roller is recommended. The roller should be well loaded for ease of application. A heavy roller pattern will be left on the substrate, therefore it is important to use a finishing tool to produce a smooth coating, with a uniform 0.75 mm wet film thickness.
Curing
Allow Vetoproof S to cure for at least 7 days prior to commissioning. At higher temperatures 30ºC cure for 4 days. At lower temperatures 12ºC cure for 10 days.
Cleaning
Immediately following application, clean all tools and equipment with clean water. Hardened material can be removed by mechanical means.
All surfaces should be dry and free from contamination such as oil, grease, loose particles, decayed matter, moss algal growth, laitance, and all traces of mold release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with a Saveto repair system. Any running water should be stopped with a suitable plugging mortar such as Vetoproof CR747. For further advice, consult the local Saveto office.
Vetoproof S powder is irritating to the eyes, respiratory system and skin. Avoid inhalation of dust and wear suitable respiratory protective equipment.
Vetoproof S liquid is not classified as dangerous. Vetoproof S when mixed becomes highly alkaline. Wear suitable protective clothing, gloves and eye protection. For both components and for the material when mixed avoid contact with eyes or skin rinse immediately with plenty of water and seek medical advise. For further information please refer to the Product Safety Data Sheet.
Vetoproof S is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Single component flexible hybrid roof water proofing membrane
Single component acrylic waterproofing membrane
Single component elastomeric crack-bridging cementitious waterproof membrane
Single component flexible pure acrylic waterproofing membrane
Polymer modified water resistant cementitious top coat
Premixed 10 to 30 mm thick cementitious screed.