Flooring Systems
Vetotop UC375

UV resistant, gloss finish easy to clean solvent-based polyurethane wall coating


High abrasion resistant walls.
Interior and exterior applications.
Institutional and high traffic areas.
Fast Download
Technical Data Sheet
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetotop UC375 is a clear two component, solvent based UV resistant urethane sealer. It is used as UV resistant sealer over masonry, concrete, gypsum and various decorative finishes. The material has excellent adhesion to minimally profiled concrete. Vetotop UC375 is UV stable for use in exterior applications, cures rapidly and the sealed system is ideal for all weather exposure. When used as a finish coat, Vetotop UC375 gives a hard, glossy surface that offers excellent stain resistance and easy cleanability. Vetotop UC375 is supplied in a pack size of 4 liters kit consist of Resin & Hardener.


  • Excellent adhesion. 
  • UV Resistant - does not yellow.
  • Good chemical resistance.
  • Durable and low maintenance cost. 
  • Excellent resistance to a wide range of mild chemicals. 
  • Tough with excellent impact and abrasion resistance. 
  • Elastomeric. 
Packaging & Coverage

Vetotop UC375 is supplied in 4 Liters Kit, Theoretical Coverage 2.5 - 5.0 m2 / Liter / coat

Vetoseal XX777-25 is supplied in 5 Liter Jerrycan, Theoretical Coverage 4 -10 m2 / Liter / coat

Stated consumptions data are for general guidance. Actual consumption depends on the nature of substrate, method of application and wastage.

Shelf Life & Storage

Original sealed kits of Vetotop UC375 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.


Application Information
Instructions for use

Mixing Vetotop UC375

In a separate plastic mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied taking care to ensure all containers are scraped clean. Do not add solvent thinners or water at any time.

Let the mixed material remain in covered container for 1-2 minute prior to use.


Apply Vetotop UC375 by roller or brush to the surface. The application should be at a rate of 2.5-5.0 m2 /liter per coat. 

Application should not be carried out when humidity exceeds 85% or drops below 5%, or when the surface temperature to be coated is less than 3°C above the dew point.

Do not apply in direct sunlight or when ambient temperatures are above 40°C or below 7°C.


Tools and equipment should be cleaned with Saveto Solvent XX300.


Surface Preparation

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. 

Laitance and weak surface layer shall be removed using mechanical methods such as grinding in order to provide a sound well profiled surface. All necessary repairs should be made prior to application. 

New concrete shall be at least 28 days old with moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Substrate Priming

Vetotop UC375 can be applied directly to most sound surfaces. However, if the surface is highly absorbent or powdery in nature; then priming is recommended using Vetoseal XX777-25. 



Design Criteria


Vetotop UC375 is designed to be applied by roller or brush as a single coat. The product is designed to resist ultraviolet rays (UV) while being cleanable and abrasion resistant.


Additional Information
Health & Sefety

Vetotop UC375 is irritant and harmful therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice. 

In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetotop UC375 and Vetoseal XX777-25 are flammable. Keep away from open flames. Refer to product(s) MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.


More Products from this section
Vetodeck UD

Polyurethane based heavy duty, waterproof and UV resistant car park decking system

Vetograin Range

Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

Vetotop CL530
Premixed 2 to 10 mm thick cementitious self leveling underlayment


Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

view more
Featured Product
Vetogrout CG518
Chloride free nonmetallic non- shrink grout


Chloride free nonmetallic non- shrink grout

Precast panels wall and base segment grouting
Repair of broken structural concrete elements where large segments are of concern
Casting structural members and elements where conventional grouts can not perform
Base plate grouting where sections are in excess of 70 mm
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com