Waterproofing
Saveto Cool Top

Single component flexible hybrid roof water proofing membrane

Uses
Waterproofing of concrete, metal, cement, and gypsum board surfaces.
Protecting bitumen and PVC roofing membranes with a high value of SRI.
Waterproofing of corrugated sheets and sloped roofs.
Fast Download
Technical Information
Product Description

Saveto Cool Top is a single component elastomeric water-based acrylic / PU hybrid membrane that has versatile uses for waterproofing in residential and commercial construction. The product is white in color with a high solar reflective index (SRI) that ensures better thermal roof insulation. Saveto Cool Top has a high resistance to yellowing, and color fading, as well as excellent dirt pick up resistance.

Advantages
  • It reflects sun rays, making it a cool roof coating.
  • Flexible elastomeric product.
  • Easy to use single component.
  • UV and color stable.
  • Excellent weathering resistance.
  • It can be applied over sloped roofs.
  • Easy to maintain.
  • Dirt-pickup resistance.
  • Resists impact damage and foot traffic.
  • Excellent to refurbish existing roofs without replacing them.
  • The right solution for small and complicated roofs.
Packaging & Coverage

Saveto Cool Top is supplied in 20kg Pails.

Theoretical Coverage of 0.7-1.2 kg/m2/coat.

Stated consumption data is for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Saveto Cool Top has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colors
White
Application Information
Instructions for use

Application

Apply Saveto Cool Top by brush, roll, or airless spray machine. Prime porous cementitious surfaces with Vetoprime AP443 at the rate of 5m²/liter and allow it to dry before applying the first coat. Use the first coat of Saveto Cool Top at the rate of 1.2 - 1.9m²/kg and allow it to cure for 4 - 12 hours depending on the ambient temperature.

Apply the second coat perpendicular to the first coat at the same rate above and allowed it to cure.

It is recommended for heavy pedestrian traffic to use fiberglass scrim reinforcement, embedded firmly in the second coat while wet, and a third coat should be applied.

Cleaning

Remove Saveto Cool Top product from tools, equipment, and mixers with clean water before the initial set. Cured material can only be removed mechanically.

Surface Preparation

All surfaces should be dry and free from contamination, such as oil, grease, loose particles, decayed matter, moss algal growth, laitance, and all traces of mold release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae, or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with a Saveto repair system.

Concrete substrates should be at least 14 days old, bituminous and PVC substrates should be 3 months old before overcoating with Saveto Cool Top.

Limitation

Saveto Cool Top should not be applied at ambient temperatures below 5°C and dropping.

Saveto Cool Top should not be applied on surfaces expected to suffer from rising dampness or relative humidity greater than 75%.

For further information contact our technical department.

Additional Information
Health & Sefety

Saveto Cool Top contains hybrid acrylic PU polymers, which can be harmful to the skin. During use, avoid contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection, and respiratory protective equipment. The use of barrier creams provides additional skin protection. In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.

Saveto Cool Top is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof AM763

Single component acrylic waterproofing membrane

Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof AM764

Single component flexible pure acrylic waterproofing membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

view more
Featured Product
Vetoproof CR747

Rapid setting cementitious water plugging mortar

Uses
Temporary patching and stop flowing water from concrete and masonry segments.
Emergency water stopping of service entry points in manholes or broken cementitious pipes at low pressure.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com