Two component solvent free epoxy primer
Vetoprime EP391 is a two-component solvent-free epoxy. It is a specialty industrial primer for the Vetorep and Vetotop product range. It is applied to prepared concrete and cementitious substrates to seal the substrate and enhance bonding with topcoats. The product can be used as a stand-alone product in internal applications as a seal coat to harden cementitious surfaces and prevent dusting. Vetoprime EP391 designed to be the ideal primer for damp concrete.
Pack Size: Vetoprime EP391 is supplied in a 4liters kit
Coverage: 28-40m2/kit
Stated consumptions data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.
Original sealed containers of Vetoprime EP391 have a shelf life of 12 months provided to store clear of ground in a dry shaded place below 35ºC.
General Applications
Priming of joint edges to receive urethane, epoxy, and polyurea based sealants.
Priming of concrete slabs and walls to receive solvent free epoxy, urethane, MMA, polyurea, hybrid coatings, screeds, and self-smoothening toppings.
Priming of concrete substrates to receive epoxy and urethane based repair mortars.
Priming of cementitious screeds to receive epoxy, urethane, and resinous toppings.
Priming
Mix Vetoprime EP391 as supplied. Add the entire content of the hardener container to the base container and mix thoroughly for about 2 minutes. Once mixed, apply the Vetoprime EP391 immediately in a thin continuous film using stiff brushes or rollers. Avoid over-application and puddles.
Allow Vetoprime EP391 to become tack-free prior to the application of epoxy coating (unless otherwise specified) but well within the open time specified for the given temperature.
The hotter the substrate, the more quickly the primer will become dry.
Cleaning
Clean all tools and equipment immediately after use with Vetonit Solvent XX400.
It is essential to apply Vetoprime EP391 to a sound and clean surface in order to achieve maximum bond strength between the substrate and the coating/repair products.
Concrete Substrates
Concrete substrates should be at least 28 days old and the relative humidity of the concrete is 75% or below. Remove laitance deposits on new concrete by light grit blasting, mechanical scrabbling, or grinding.
Where heavy contamination by oil and grease occurs or existing coatings present, it is essential to remove all contaminations.
At temperatures below 20ºC, the cure rate will be slower. Conversely, at temperatures above 20ºC, the cure rate will be faster.
Some people are sensitive to epoxy resins; so gloves and a barrier cream shall be used when handling these products. If contact with the resin occurs, it must be removed, before if hardens, with a resin removing cream follow by washing with soap and water. Do not use solvent.
During use, avoid inhalation of solvent and contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection, and respiratory protective equipment. In case of contact with the eye, rinse immediately with plenty of clean water, and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.
Vetoprime EP391 is non-flammable.
Refer to Material Safety Data Sheet for further information.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Multi-purpose bonding agent & admixture
Multipurpose low viscosity bonding agent & admixture
High Quality Monofilament Polypropylene Fibers
Polymeric soil stabilizer
Polymeric bonding agent, waterproof mix enhancer & primer
Acrylic polymer modified decorative finish coat applied at thicknesses from 3 to 20 mm