Waterproofing
Vetoproof UM765

Elastomeric polyurethane liquid applied waterproofing membrane

Uses
Wet areas: kitchens, bathrooms, swimming pools, etc.
Basements, tunnels, subways and culverts
Inveted roofs, suspended slabs, balconies
Tanking systems
Fast Download
Technical Data Sheet
download (*.pdf 0.13Mb)
Method of Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetoproof UM765 is a premium quality pitch extended polyurethane waterproofing membrane, the product is liquid applied that hardens through reaction with atmospheric water vapour to form a highly elastic rubbery jointless membrane that is resistant to aggressive ground water and sewage. The product is available in two grades: UM 765-H and UM765-V for both horizontal and vertical applications respectively. Detailing around pipe entries and corners can be made with UM765-V and can be reinforced with glass fi ber mesh or non-wooven fibers.

Advantages
  • Easy to apply single component liquid application
  • Jointless application that is easy to detail
  • Crack bridging highly elastic membrane at various temperatures
  • Vapour proof
  • Available in two grades for horizontal and vertical applications
  • Easy to repair and maintain
  • Fully bonded prohibiting lateral migration of water
  • Thermally and chemically stable, resistant to oxidation and embrittlement
Compiliance Standard

- ASTM C836/C836M (2012)

- ASTM C1417/C1417M-05 (2014) e1

- ASTM C898/898M-2009

Packaging & Coverage

Vetoproof UM765 supplied in 20 Liters Pails (27kg)
Coverage - 1.3kg/ m²@1 mm thickness

Shelf Life & Storage

Original sealed bag of Vetoproof UM765 has a shelf life of 12 months provided it is stored in original sealed containers clear of ground in a dry and shaded place below 35ºC.

Colors
Black
Application Information
Instructions for use

Design Criteria

Vetoproof UM765 use follows the guidelines of EN BS8102:2009 and CIRIA report No. 139 and ASTM guides C1417 nad 898.

Priming

Priming is not usually required on good quality concrete substrates. However, for highly porous or absorbant concrete; dilute Vetoproof UM765 at a ratio of 1:1 with Vetonit Solvent XX and use as a prime coat.

Application

Vetoproof UM765 should be applied by brush, trowel or a gaged spreader at a minimum thickness of 1 mm. Use the right grade (H or V) and the thickness can be achieved in one pass. Use Vetoproof UM765-V for detailing works around pipe entries and corners prior to the application of Vetoproof UM765 H. Glass fiber scrim and joint tapes can be used on corners and critical areas for reinforcement of the membrane. Tiling over Vetoproof UM765 is possible, in such cases sharp sand needs to be sprayed over Vetoproof UM765 while still wet, 24 hours later all excess sand is to be removed and a suitable tile adhesive from Saveto range can be used to bond the tiles directly over the membrane.

Curing

Vetoproof UM765 must be allowed to cure for a minimum of 24 hours prior to placing protection. Where damage to the membrane is possible; the membrane needs to be protected by a cementitious screed or protection boards. Note: Vetoproof UM765 is not resistant to UV light, in case of external non protected applications use Vetoproof UM766 or UM767. Please refer to product TDS for more information.

Cleaning

All tools employed for the application of Vetoproof UM765 can be cleaned with Vetonit Solvent XX400 before it hardens otherwise mechanical means are needed.

Surface Preparation

All surfaces where Vetoproof UM765 has to be applied must be clean and have an open capillary system. Eliminate laitance, dirt, grease and other loose materials by means of high pressure water jetting or wet sand blasting. Defective concretes such as cracks and honeycombs, etc. has to be chased out and repaired prior to the application.

Additional Information
Health & Sefety

Some people are sensitive to resins, hardeners and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, suitable respiratory protective equipment must be used. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medial advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetoproof UM765 is flammable, do not use near to open flames. Refer to product MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof AM763

Single component acrylic waterproofing membrane

Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof AM764

Single component ultra flexible acrylic waterproofing membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

view more
Featured Product
Vetotop AC442

High performance aliphatic acrylic protective & decorative coating for concrete and masonry

Uses
To protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, sulphates, oxygen and water.
Suitable to protect all types of structures, cementitious substrates, masonry and aggressive marine and coastal environments.
Suitable for new and existing structures.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map