Concrete Grouts Repair and Enhancement
Vetorep ER350

Twin pack epoxy putty, sealing, anchoring and leveling compound

Uses
Repair of concrete surface pores, blemishes at thickness from feather edge.
Sealing of surface cracks in aggressive environments and in injection repairs.
Leveling of surface imperfections and irregularities prior to application of Saveto resinous coatings and toppings range.
Fixing and bedding of tiles, dowels and anchors.
Fast Download
Technical Data Sheet
download (*.pdf 0.28Mb)
Method of Statement
download (*.pdf 0.21Mb)
Technical Information
Product Description

Vetorep ER350 is a two component epoxy based thixotropic solvent free compound. Once components of the kit are mixed the products becomes a smooth paste that is used to repair surface imperfections and irregularities, fill blow holes and pores while being completely impermeable and having excellent adhesive and bonding properties. The thixotropic nature of the products allows it to function in vertical and overhead situation without sagging while maintaining excellent bond.

Advantages
  • Smooth paste consistency that is non-slump.
  • Chemically resistant compound.
  • Superior bond to a wide range of substrates.
  • Compatible with most coating and topping types.
  • Can be feather edged and built up to a thickness of 3 mm in a single layer.
  • Extremely effective in cases of low reinforcement steel concrete cover.
Packaging & Coverage

Vetorep ER350 supplied in 1 & 5 Kg kits.

Consumption - 0.7 Liters / Kg.

Shelf Life & Storage

Original sealed kits of Vetorep ER350 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded temperature controlled place <35ºC.

Application Information
Instructions for use

Mixing
Vetorep ER350 comprises two components, a resin Base and a Hardener, which are supplied preweighed in the correct proportions. Under no circumstances should part mixing be carried out. When required for application, the two components should be mixed well until a uniform consistency and color are obtained, this should be ideally carried out using a mechanical mixer. Mixing of 1 kg packs can be done by hand but care must be taken to ensure homogeneous mixing. In cold weather, mixing will be aided if the containers are stored in a warm environment before use.
For bonding concrete sections, an even coating of product should be applied to both surfaces and these brought together under light pressure. Any excess paste which exudes from the joint should be removed and the joint trowelled to a neat finish. The assembled sections should be protected from movement until the resin is set. Where Vetorep ER350 is to be used as a bonding primer in the vertical or overhead position, an even layer of Vetorep ER350 should be applied to the surface and worked well in to ensure good contact. The material to be bonded should then be placed after approximately 30 minutes at 20ºC. (This time refers to the total elapsed time from mixing the product). For patch repairs, Vetorep ER350 should be applied to the surface and finished to levels. A smooth surface will be aided by wetting the trowel sparingly with Vetonit Solvent XX400. Vetorep ER350 can be applied to cracks or in accessible areas by means of a sealant gun.
Vetorep ER350 has a working time of approximately 45 minutes at 20°C. Mixed material should not be left standing for any length of time prior to application, as this will considerably reduce its working time.

Curing
Vetorep ER350 shall be allowed to cure for 24 hours at 20°C before being subjected to foot traffic. At the same temperature, full mechanical and chemical properties are achieved after 7 days (please consult Saveto Technical Department for details of curing times at other temperatures).

Cleaning
Clean uncured material with Vetonit Solvent XX400. Cured material can only be removed mechanically.

Surface Preparation

The surface must be structurally sound, free from oil, grease and other forms of contamination. Concrete should be surface dry and suitably prepared either by scabbling or grit blasting to remove any surface laitence.
Steel surfaces should be grit blasted to remove all rust and scale.

Additional Information
Health & Sefety

Vetorep ER350 Contains resins which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed seek medical attention immediately. Do not induce vomiting.
Vetorep ER350 is non-flammable.
Vetonit Solvent XX400 is flammable, do not expose to direct flame and keep away from heat sources.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

Vetocure XT425

Water based concrete curing compound

Vetocure XT426

Resinous, render receiving concrete curing compound

Vetocure XT427

Water based acrylic curing compound and primer

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

view more
Featured Product
Vetorep ER352

Twin Pack Putty Formulated for Thick Vertical and Overhead Applications

Uses
Repair of concrete surface pores, blemishes at thickness from feather edge.
Sealing of surface cracks in aggressive environments and in injection repairs.
Leveling of surface imperfections and irregularities prior to application of Saveto resinous coatings and toppings range.
Fixing and bedding of tiles, dowels and anchors.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map