Weather-resistant stainless non-sanded smooth tile jointing grout
Stainless Grout is a cementitious mortar adhesive composed of hydraulic binders, selected aggregates, polymer-modified, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar. Stainless grout eliminates the need for a sealer. Stainless Grout is applied in thickness from 2-4 mm for wall tiles and 3-8 mm for floor tiles.
Hydrophobicity properties for stain resistance, uniform color & durability.
Factory controlled pre-blend ensures consistently high quality.
Requires only the addition of water on-site at the time of usage.
Easy tile installation that enables high productivity.
Excellent bonding on a variety of ceramic tiles available in the local market.
Suitable for internal & external applications.
Suitable for horizontal & vertical surfaces.
BS: EN 13888 as CG2AW
SASO ISO 13007-3,4 as CG2AW
Stainless supplied in 20Kg Bag.
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastages.
The original sealed bag of Stainless Grout has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.
For Stainless Grout mortar's preparation, pour into a container 5-6.4 Liters of water for a 20kg bag of Vetonit Stainless Grout. Add the powder to the water and mix with a low-speed electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency. Allow the mixed material to stand for about 10 minutes and remix briefly without adding water.
Blend Vetonit Pool Grout manually for small quantities and maintain the correct mixing ratio of powder to water.
If required, add 0.5 Ltr of Saveto Bond 2 to the mixing water, followed by powder's addition. Use the mixed material within 1 hour.
Do not add water to the mixture once the mortar grout starts to harden.
Apply Vetonit Stainless Grout using either a rubber blade, a grouting trowel, a rubber spatula, or a sponge.
Spread the mixed grout diagonally across the tile joints and firmly press it with a rubbing pad covered with a sponge rubber spatula to ensure filling all the gaps.
Remove excess grout that remains on tiles using the same tool.
After the grout initially dries, from 15-30 minutes, depends on the ambient temperature & humidity, clean the tiles and remove all excess material with a wet sponge.
After full drying, clean the surface of the tiles with a dry cloth or dispensable cotton towels.
When washing & drying the tiles, ensure not to rub the tile joints too deep.
Keep the grout moist for the first 2 days after application to ensure achieving good hardened properties.
Clean tools and equipment with water immediately after use. Hardened materials will require removal by mechanical means.
Remove all tile adhesive excess that is at a level higher than half of the tile thickness.
All the joints should be free from dust, loose materials & traces of foreign materials, etc. Neutralize the tiles' water absorption by applying clean potable water.
Do not leave water pooling in the joints.
Stainless Grout is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Stainless Grout is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather-resistant cementitious adhesive for ceramic tiles
Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles
Water-resistant grout for swimming pool tile joints
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
Premium quality premixed compound for gypsum board joints