Professional grade cementitious non sanded tile grout
Vetofill CG550 is a polymer-modified cement-based professional-grade and water-resistant tile grout used with most types of tiles, including ceramic, porcelain, glass mosaic, marble, granite,...etc. The product is composed of a blend of cement, special additives, selected fillers, and polymers. Once mixed with water, the product becomes an easily workable creamy mortar.
Easy to apply a single component.
Excellent mechanical and physical properties.
High bond strength.
High abrasion resistance.
Low water permeability.
Suitable for internal and external applications.
Suitable for use on horizontal and vertical tile applications.
Low VOC environmentally friendly Product.
SASO ISO 13007-3, 4 as CG2AW
BS: EN13888
Vetofill CG550 supplied in 20Kg Bag.
Consumption: 1.2 - 1.4 Kg / m2 / mm.
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastages.
The original sealed bag of Vetofill CG550 has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.
Mixing
Add 6 to 7.2 Liters of fresh, clean water to a suitably sized mixing vessel. Slowly add the powder component while mixing using a mixer fitted with a Saveto approved paddle for 3 to 5 minutes until achieving a uniform, lump-free consistency. Allow the mixed material to mature for about 10 minutes and remix briefly.
Important Note: Do not mix partial quantities unless an exact proportion based on volume can be achieved using proper tools.
If performance enhancement is required, add 0.5 liters of Vetobond PB434 to the mixing water, followed by powder's addition.
Use the mixed material within 4 hours.
Do not add water to the mixture once the mortar grout starts to harden.
Application
Apply Vetofill CG550 using either a rubber blade, a grouting trowel, a rubber spatula, or a sponge. Spread the mixed grout diagonally across the tile joints and firmly press it with a rubbing pad covered with a sponge rubber spatula to ensure filling all the gaps.
Remove excess grout that remains on tiles using the same tool.
After the grout initially dries, from 20-30 minutes, depends on the ambient temperature & humidity, clean the tiles and remove all excess material with a wet sponge. After full drying, clean the surface of the tiles with a dry cloth or dispensable cotton towels.
When washing & drying the tiles, ensure not to rub the tile joints too deep.
Keep the grout moist for the first 2 days after application to ensure achieving good hardened properties.
Cleaning
Clean tools and equipment with water immediately after use. Hardened materials will require removal by mechanical means.
Remove all tile adhesive excess that is at a level higher than half of the tile thickness.
All the joints should be free from dust, loose materials & traces of foreign materials, etc. Neutralize the tiles' water absorption by applying clean potable water.
Do not leave water pooling in the joints.
Vetofill CG550 is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetofill CG550 is non-flammable.
For further information, please refer to the material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather-resistant cementitious adhesive for ceramic tiles
Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles
Water-resistant grout for swimming pool tile joints
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
Extruded polystyrene panels for ETICS