Polymer modified weather resistant multipurpose adhesive for tiles.
Vetonit Ultra is a cementitious mortar adhesive composed of hydraulic binders, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce easily workable mortar. Vetonit Ultra is ideal for fixing Tiles, Terrazzo Tiles, Marbles, and Riyadh stones. Vetonit Ultra is applied in thickness from 3mm to 10mm, it depends upon the type of tiles and quality of the substrate.
BS:EN 12004 as C2TE SI
SASO ISO 13007-1: C2TE S1
Vetonit Ultra is supplied in 20Kg Bags.
Coverage:
Walls: 6.0 - 6.5 m²/20kg bag
Floor: 4.5 - 5.5 m²/20kg bag
Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastages.
An original sealed bag of Vetonit Ultra has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.
Mixing
For the preparation of mortar adhesive, pour into a container 5-6.8 liters of water for each 20Kg bag of Vetonit Ultra.
Add the powder to the water and mix for 3-4 minutes using a low- speed electric drill fitted with a suitable paddle until achieving a uniform, lump-free consistency. Allow the mixed material to stand for about 10 minutes and remix briefly without adding further water.
Blend Vetonit Ultra manually for small quantities but ensure to maintain the correct amount of powder to water.
If required, add 0.5 Ltr of Saveto Bond 2 to the mixing water, followed by powder's addition. Use the mixed material within 2 hours.
Do not add water to the mixture once the mortar adhesive starts to harden.
Application
Spread the mixed mortar adhesive, and firmly press it onto the surface that will be tiled; work with a notched trowel. Spread the mortar adhesive to an area that can be tiled within 10-15 minutes. Press the tiles firmly over the mortar adhesive and immediately knock them into the desired position. Adjust the position of the tiles, if required, within its adjustability time of 10-15 minutes after installation.
Allow the installed tiles to remain undisturbed for at least 48 hours. Mortar adhesive must not rise between the tile joints higher than halfway the thickness of the tiles. It is recommended to use Vetonit Tile Grout to fill the joint gaps after 2 days of tile installation.
Cleaning
Clean tools and equipment with water immediately after use. Remove the hardened material using mechanical means.
The substrate should be sound, clean, free from loose material, oil, grease, laitance, dirt, curing compound, etc.
Wet all surfaces (except gypsum board) with clean water before the application of Vetonit Ultra. The surface should appear damp with no water pooling.
Vetonit Ultra is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.
Vetonit Ultra is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather-resistant cementitious adhesive for ceramic tiles
Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles
Water-resistant grout for swimming pool tile joints
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
Multipurpose bonding agent & admixture