Cementitious premixed plastering/rendering Material
Premix Plaster SF is a cement-based plastering material composed of hydraulic binders, natural sand, selected graded aggregates, special fibers, and special additives. It is supplied as a dry powder in bags/bulk ready to use on-site, which requires only the addition of clean water to produce cohesive mortar. Premix Plaster SF is specially designed for application by spray machine. It can be used manually if required, and contains a special shrinkage control additive, and provides good adhesion with a uniform color surface. Premix Plaster SF can be applied at thicknesses ranging from 10mm to 25mm.
Premix Plaster SF supplied in 50Kg Bag or Bulk.
Yield - 31.25 Liters.
Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.
The original sealed bag of Premix Plaster SF has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place, at temperatures between 5ºC - 35ºC.
Design Criteria
Premix Plaster SF is designed to be used at thicknesses between 10 and 25mm in a single application. The product can be applied on block walls without using a scratch coat as long as the substrate is properly neutralized before application.
Mixing
Add to the mixing container 6.5-8.5 liters of water for each 50Kg bag of Premix Plaster SF. Add the powder to the water and mix with a mechanical plaster mixer or low-speed electric drill fitted with a suitable paddle for 3-4 minutes until achieving a uniform, lump-free consistency.
For PFT plastering machine application, the water flow rate should be 350- 550 lit/hr, depending on the rubber pump's status. Use the mixed material within 90 min.
Do not add water to the mix once the mixed mortar starts to harden.
Smooth Concrete Surfaces
Apply Spatter Dash SB before the application of Premix Plaster SF.
Application
Apply Premix Plaster SF in single or multiple layers on rough surfaces. On smooth surfaces, apply it after the application of a spatter dash coat.
When the plaster starts to set, rod or level to a uniform thickness, then smoothen the material to the desired appearance.
For multiple layers, follow the practice in ASTM C926, 10 - 15 mm/layer with a rough finish, curing for two days /layer before applying the second one. Finish the final layer as desired.
After the surface appears stiff but still moist, smoothen the material's surface to achieve the desired appearance.
Curing
Cure Premix Plaster SF by spraying water on its surface every 8-12 hrs for a minimum of 3 days. During hot & dry conditions, allow curing for a minimum of 5 days. It will help to obtain high mechanical strengths and minimize the risk of surface cracks.
Cleaning
Clean tools with water before the mortar hardens. After the hardening, remove the residuals mechanically.
The substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, or any other substance that might impair the substrate's quality of the bond. Before the Premix Plaster SF application, damp the entire surfaces with clean potable water. The substrate should be neutralized surface at the time of the Premix Plaster SF application.
Ensure the substrate is suitable for the application of Premix Plaster SF; in case of doubt, try on a sample area to assess its suitability.
Do not apply the product under direct rain, extreme wind, and temperatures below +5ºC or above +45ºC.
Premix Plaster SF is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap and water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice. Premix Plaster SF is non-flammable.
For further information, please refer to the material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High-quality lightweight premixed acoustic plaster
Premixed cementitious masonry grout
Sprayable lightweight premixed plaster
High-quality gypsum plaster
Light weight gypsum perlite plaster
Water based concrete curing compound