Renders & Finishes
Vetonit Putty WR

Water resistant high quality premixed putty

Uses
Use to leveling of minor surface undulations.
Apply externally & internally, in wet and dry conditions, onto the walls & ceilings such as Bathrooms & Kitchens.
Use on concrete and plastered surfaces that are smooth, and also on precast concrete surfaces.
Suitable for use over surfaces that are plastered with Saveto products and on gypsum boards.
Fast Download
Technical Information
Product Description

Vetonit Putty WR is composed of fine fillers, bonding chemicals, and high-performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site. It only requires the addition of clean water to produce a cohesive mix. Vetonit Putty WR is a high-quality product applied as a thin underlayment to repair undulations. It provides a very smooth surface finish that is ideal for subsequent application of paint and decorative coatings. Vetonit Putty WR can be applied generally in thickness from 1mm to 3mm.

Advantages
  • Factory controlled pre-blend that ensures consistently high quality.
  • It requires only the addition of water on-site at the time of usage.
  • Suitable for external & internal applications.
  • Water-resistant.
  • It is easy to apply as it requires minimum effort to achieve a superior finish.
  • Strong adhesion on a variety of substrates.
  • Use on concrete and plastered walls & ceilings.
  • It achieves a very smooth finish.
  • It is suitable for humid & dry conditions.
COMPLIANCE STANDARD
  • BS EN 1015-12 
Packaging & Coverage

Vetonit Putty WR is supplied in 20kg Bags.
Consumption: 1.0 - 1.2 Kg/m2/1mm Thickness

Stated consumptions data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

Shelf Life & Storage

An original sealed bags of Vetonit Putty WR have a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 25ºC.

Colors
White color powder
Application Information
Instructions for use

Mixing

For mechanical mixing, add to the mixing container 7.6-8.8 liters of water for each 20kg bag of Vetonit Putty WR. Add the powder to the water and mix with a mechanical plaster mixer, or with a low-speed electric drill fitted with a suitable paddle. Mix for 3-4 minutes until achieving a  uniform, lump-free consistency.

Leave the mixed material to stand for 10 min and briefly remix without adding water.

Mix small batch quantities manually for approximately 1-2 min, or until achieving a when a homogenous mix.

When required, add 1 liter of Vetonit Bond 2 to the mixing water and adjust the water requirement for each 20kg bag of Vetonit Putty WR accordingly. Follow the same mixing procedure as above.

Use the mixed material within 3 hours. Do not add water once the mixed filler mortar starts to stiffen or harden.

Application

Generally, apply Vetonit Putty WR is in single or double coats.

Apply Vetonit Putty WR to the substrate by pressing the putty firmly onto it. Use a flat trowel to level the material to a smooth finish.

Apply a second coat if necessary, once the first coat initially sets.

After applying Vetonit Putty WR, it is recommended to apply one coat of alkali-resistant primer followed by two coats of acrylic emulsion paint or other suitable coatings.

Curing

Vetonit Putty WR is self-curing and it does not require water treatment. However, when using Vetonit Putty WR as a final finish, it is recommended to apply a single coat of Bond Pure. The bonding agent will perform as a surface enhancer, and as a curing compound that will naturally disintegrate with time.

Cleaning

Clean all tools immediately after finishing by water. Clean the hardened materials mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Prior to the Vetonit Putty WR application, wet the entire surfaces with clean potable water. The surface should look damp at the time of the Vetonit Putty WR application.

Additional Information
Health & Sefety

Vetonit Putty WR is highly alkaline therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during the application. Wash any skin contact with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Vetonit Putty WR is non-flammable.

For further information, please refer to the material safety data sheet.

Important note
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Putty Fine

PVA copolymer based high-quality putty

 

Vetogyps Compound
Gypsum surfaces skim and finish compound

">

Gypsum surfaces skim and finish compound

Vetonit Crack Filler

High quality premixed surface crack filler

Vetonit Finish WR

Water resistant internal use premix smooth cement coating

Vetonit Finish WR EG

Water-resistant external use premix smooth cement coating

view more
Featured Product
Vetorep CR521

High strength structural non-shrink self-compacting micro concrete

Uses
Repair of broken structural concrete elements where large segments are of concern
Concrete repair were high steel congestion is present
Repairs with thickness of 50 to 400 mm
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com