Heavy duty polyurethane hybrid flooring system
Vetotop US172 is a single layer, seamless, solvent-free, polyurethane-based flooring system. its textured matt finish possesses excellent chemical resistance, withstands abrasive wear; has high impact resistance and withstands direct steam contact and cleaning practices.
Vetotop US172 is supplied in 30kg Kit with coverage: 2.1-2.3 kg m2 at 1mm thickness
An original sealed Kit of Vetotop US172 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 30ºC.
Vetotop US172 is designed to be a hard-wearing trowel-applied Polyurethane screed on cementitious or metal substrates at thicknesses 6, 9, or 12 mm. The applied product will be resistant to water as well as a wide range of chemicals.
All surfaces receiving Vetotop US172 can be applied directly to sound and non-porous concrete.
Vetotop US172 is supplied in three pre-weighed packs (base, hardener, and aggregate) which are ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both the performance and the appearance of the finished floor. Mixing should be carried out using either a forced action mixer; or a heavy-duty mobile mixer fitted with a suitable jiffy type mixing paddle. All such equipment should be of a type and capacity approved by Saveto. The components should be mixed in a suitably sized mixing vessel. Stir the base and hardener components individually then empty them into the mixing vessel scrapping the edges and mix for 2 minutes. The contents of the graded aggregate pack should be slowly added and mixing carried out for a further 3 minutes until a completely homogeneous material is obtained.
Vetotop US172 should be spread to uniform thickness on the primed surface using either a screed box or the edge of a steel trowel. The material should be tamped with a wooden float to ensure complete compaction and finally finished to a closed even texture using a steel trowel. Screeding rods are useful to maintain a minimum compacted thickness of 6 mm. The material must be applied within the pot life after mixing.
Although Vetotop US172 is impervious at 6 mm thick in constantly wet operations areas or where a high degree of cleanliness is required.
All tools and equipment should be cleaned immediately after use with water.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting in order to provide a sound well-profiled surface. All necessary repairs should be made prior to the application by using the same material. New concrete floors shall be at least 5 days old and visibly dry with no standing water on top.
Grooves must be cut in concrete to control shrinkage. Please contact Saveto for further advice.
Vetotop US172 should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well-ventilated areas. In case of insufficient ventilation wear suitable respiratory protection. Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection.
Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.
Refer to product MSDS for further information.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water based chemical & abrasion resistant antibacterial wall & floor thin epoxy coating
High performance, aromatic & flexible waterproof polyurethane flooring membrane