Single component elastomeric crack-bridging cementitious waterproof membrane
Vetoproof CM740 is a single component flexible polymer modified cementitious waterproof membrane. It has unique crack bridging characteristics even after long-term water immersion. The product is suitable for use and contact with potable water and can withstand negative hydrostatic pressure. The product also complies with the requirements of ANSI 118.12 for crack isolation and use in tile fixing assemblies.
Vetoproof CM740 is supplied in 20 Kg Bag.
Coverage - 15 m2/bag/mm
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, consistency used, method of application, and wastage.
The Original sealed bag of Vetoproof CM740 and has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.
Mixing
Pour 5 to 7 liters of fresh, clean water into a suitably sized mixing container. Commence mixing with a propeller agitator attached to a slow speed drill (300-500 rpm). Add the powder component gradually to the liquid to avoid lump formation and mix for 2 to 4 minutes. Use Vetoproof CM740 immediately after mixing. Do not mix more material than the amount that can be used within the pot life. Keep mixing Vetoproof CM740 during the application.
Application
For best results, surfaces should be damp. To obtain the protective properties of Vetoproof CM740, the correct rates of the application must be observed. Use a short, stiff brush, preferably 120 - 200 mm width, and apply in two or three coats as required. Use the correct mixing ratio to obtain satisfactory consistency for spray or trowel applications. Spray application will likely be the best for exterior decorative finishes in hot climatic conditions. Use nozzle size 3 - 4 mm, and a pressure of 6 - 8 bars.
The application of Vetoproof CM740 should not commence if the temperature of the substrate is below 5ºC. Application of Vetoproof CM740 on hot substrates, i.e., over 40ºC surface temperature, will need a primer coat of mixed Vetoproof CM740 and water slurry-like consistency. Apply Vetoproof CM740 over the primer whilst it is still wet. It is recommended that for general resurfacing, each coat should be 1mm thick. Areas subjected to light foot traffic should receive at least 2mm thickness of Vetoproof CM740, and an additional 2mm should be applied if conditions are moderate to heavy pedestrian traffic. The membrane can be reinforced using a 2x2 or 4x4 acrylic coated glass fiber mesh of 140 - 180 gm/m2 immersed in between coats. If in doubt about the condition of the substrate, consult Saveto technical department for any additional information.
Cleaning
Clean tools with water promptly before material hardens. Remove hardened material mechanically.
All surfaces should be dry and free from contamination, such as oil, grease, loose particles, decayed matter, moss algal growth, laitance, and all traces of mold release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae, or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with a Saveto repair system. For further advice, consult the local Saveto office. It is essential that all surfaces that receive Vetoproof CM740 be pre-soaked with clean water before applying Vetoproof CM740.
Do not apply the product at a temperature less than +5ºC.
For further information contact our technical department.
Vetoproof CM740 contains cement powders that release alkalies that can be harmful to the skin when mixed or become damp. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection, and respiratory protective equipment. The use of barrier creams provides additional skin protection. In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with the eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.
Vetoproof CM740 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Single component flexible hybrid roof water proofing membrane
Single component acrylic waterproofing membrane
Single component flexible pure acrylic waterproofing membrane
Polymer modified water resistant cementitious top coat
Single component penetrating waterproofing system for concrete
Chloride free nonmetallic non-shrink grout