Waterproofing
Vetoproof AM764

Single component flexible pure acrylic waterproofing membrane

Uses
Waterproofing of concrete, asbestos, metal, cement, and gypsum board surfaces.
Protecting spray-PU membranes from UV rays.
As a decorative overlay on bituminous membranes and over existing terrazzo tiles.
Waterproofing of corrugated sheets and sloped roofs.
Fast Download
Technical Information
Product Description

Vetoproof AM764 is a single component elastomeric water-based acrylic membrane with versatile uses for waterproofing in residential and commercial construction. The product is available in a variety of colors that are extremely stable in extreme weather conditions. Vetoproof AM764 is an all-cross-linking-acrylic making it resistant to yellowing, color fading, and has excellent dirt-pick-up resistance.

Advantages
  • Flexible elastomeric product.
  • Easy to use single component.
  • UV and color stable.
  • Excellent weathering resistance.
  • It can be applied over sloped roofs.
  • Easy to maintain.
  • Dirt-pickup resistance
  • It reflects sun rays, making it a cool roof coating.
Packaging & Coverage

Vetoproof AM764 is supplied in 20kg Pails.
Theoretical Coverage - 0.7 - 1.2 kg/m2/coat

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Vetoproof AM764 has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colors
Black
Application Information
Instructions for use

Application

Apply Vetoproof AM764 by brush, roll, or airless spray machine. Prime porous cementitious surfaces with Vetoprime AP443 at the rate of 5 m²/liter and allow it to dry before applying the first coat. Apply the first coat of Vetoproof AM764 at the rate of 1.2 - 1.9m²/kg and allow it to cure for 4 - 12 hours depending on the ambient temperature.

Apply the second coat perpendicular to the first coat at the same rate above, and allow it to cure.

It is recommended for heavy pedestrian traffic to use fiberglass scrim reinforcement, embedded firmly in the second coat while wet, and a third coat should be applied.

Cleaning

Remove Vetoproof AM764 product from tools, equipment, and mixers with clean water before the initial set. Cured material can only be removed mechanically.

Surface Preparation

All surfaces should be dry and free from contamination, such as oil, grease, loose particles, decayed matter, moss algal growth, laitance, and all traces of mold release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae, or similar growths have occurred, carried out treatment with a proprietary biocide after the grit-blasting process. Remove spalled and deeply disintegrated concrete to sound concrete and repair it with a Saveto Repair System.

Concrete substrates should be at least 14 days old; bituminous substrates should be 3 to 6 months old before overcoating with Vetoproof AM764.

Limitation
  • Vetoproof AM764 should not be applied at ambient temperatures below 5°C and dropping.
  • Vetoproof AM764 should not be applied on surfaces expected to suffer from rising dampness or relative humidity greater than 75%.
  • For further information contact our technical department.
Additional Information
Health & Sefety

Vetoproof AM764 contains an acrylic polymer that can be harmful to the skin. During use, avoid contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection, and respiratory protective equipment. The use of barrier cream provides additional skin protection. In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with the eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.

Vetoproof AM764 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Cool Top
Single component flexible hybrid roof water proofing membrane

">

Single component flexible hybrid roof water proofing membrane

Vetoproof AM763

Single component acrylic waterproofing membrane

Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

view more
Featured Product
Vetobond PB434

Polymeric bonding agent, waterproof mix enhancer & primer

Uses
Production of high strength waterproof renders, screeds, cement slurries and mortars
Enhancing cementitious mixes such as plasters, tile adhesives, screeds, etc.
As a primer and surface sealer for plasters and repair mortars
Enhancement of cementitious mixes to freeze and thaw cycles
Bonding old to new concrete.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com