Premixed 8 to 20mm thick polymer modified cementitious self leveling underlayment.
Vetotop CL531 is a single component polymer modified cementitious floor self leveling underlayment composed of hydraulic binders, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, once mixed it will form a cohesive self smoothening honey-like flowing mortar that is applied in thicknesses between 8 and 20mm giving a super flat finish ready to receive final floor coverings including tiles, carpets, resinous flooring systems, parquet, ...etc.
Factory controlled pre-blend ensures consistent high quality.
Suitable for Middle East harsh weather conditions.
Easy application enabling high productivity & superior finishing.
Rapid commissioning and serviceability.
High bond to substrate.
Excellent physical and mechanical properties.
Fiber reinforced resisting crack formation.
Vetotop CL531 is supplied in 25kg bags with Yield: 1.5 - 1.8 Kg/m²/mm
Original sealed bag of Vetotop CL531 has a shelf life of 6 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.
For single bag mixing add to the mixing container 4.25 – 5.0 liters of water for each 25 Kg bag of Vetotop CL531. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3 - 4 minutes, until a uniform, lump-free fluid consistency is achieved.
Try to minimize the water addition to get higher strength. Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogeneous mix is achieved.
Vetotop CL531 can be applied using screw type pump with pumping rate of 25-50 liters/min and length of hose 40-50 LM. and control the water dosage to achieve the required flow.
After placing onto the primed surface, apply by trowel or pin screed. Rake to the Vetotop CL531 spreads and adjust itself to a level floor.
For small areas Vetotop CL531 can be applied manually.
Use a suitable spike roll to remove entrapped air if there is any.
Self curing, 1 - 3 days by sealing off the area. Floor becomes ready for commissioning or topping after 3-5 days.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Larger areas can be divided with wooden battens to control the pumping volume and determine the layer thickness to be applied.
Priming the substrate is vital, use Vetoprime PB433 diluted with potable water (ratio of 1:1.5), or use Vetoprime PB435 without dilution. Mix thoroughly and spray or brush onto the floor without pooling.
Before applying Vetotop CL530, it’s important to leave the primer between 30-60 minutes to fully dry. In case of doubt, check the primer dryness by adding drops of water on top of the primer substrate, it should not absorb the water drops.
Do not mix with any additives or products, unless recommended by Saveto.
Make sure the substrate is suitable for underlayment application. In case of doubt, try on sample area to assess its suitability.
Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also air-draft during initial curing stage.
Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
For further information contact our technical department.
Vetotop CL531 is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Vetotop CL531 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy duty, waterproof and UV resistant car park decking system
Premixed 2 to 10 mm thick cementitious self leveling underlayment
Premixed 10 to 30 mm thick cementitious screed.
Premixed 30 to 100 mm thick cementitious screed.
Water based chemical & abrasion resistant antibacterial wall & floor thin epoxy coating
PVA copolymer based high-quality putty