Protective Coatings
Vetoseal XX772

High efficiency solvent-based non-staining siloxane water repellant

Uses
Transforming construction substrates to water-repelling surfaces.
Cementitious substrates: block and brickwork, pre-cast panels, and plasters.
Sealing and treatment natural stone, marble, and absorbent tiles.
As a sealer for cementitious-based Vetotouch range of EIFS/ETICS finishes.
Fast Download
Catalogues
Saveto Flooring Technical Guide
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetoseal XX772 is a solvent-based silane-siloxane penetrating hydrophobic water repellent. It penetrates the cementitious or stone substrates, reacts, and works by increasing the surface tension of water to slide away from the surface. Vetoseal XX772 allows the substrate to breathe by allowing water vapor to escape the substrate and drastically reducing water absorption and resisting the ingress of chloride ions.

Advantages
  • Single component fast easy application.
  • Cost-effective.
  • easily penetrates into substrates.
  • Non staining.
  • Reduces water and chloride intrusion.
  • Increases freeze thaw resistance.
  • Minimises effloresence.
  • Allows water vapour to escape from the structure and resistant to atmospheric contaminants.
Packaging & Coverage

Vetoseal XX772 supplied in 20 Liters Container.

Theoretical Coverage: 5 - 15 m2 / liter.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Vetoseal XX772 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Design Criteria

Vetoseal XX772 is designed to be applied by brush or low-pressure spray in two to three flood coats for maximum performance. Treating tiles by immersion of silane-siloxane solution may slightly reduce the tile bonding that relies on absorption of adhesive paste for bonding.

Application

Apply Vetoseal XX772 as a continuous flood coat using either a soft brush or low-pressure spray equipment at the correct coverage rate. For best performance, 2 to 3 flood coats are recommended with 2 to 4 hours between coats (5 m2 / Liter).

Cleaning

Clean equipment and tools using Vetonit Solvent XX400 immediately after use. If residual material exists or hardens, mechanical means such as wire brush would be required to remove residue.

Surface Preparation

Surfaces to be treated with Vetoseal XX772 must be structurally sound and free from loose materials, grease, oils, or other contaminants. If such contamination is present, it is recommended to remove these by grit blasting and using an industrial chemical degreaser. Repair cracks or holes using a recommended Saveto repair material, allow it to cure before proceeding.

Additional Information
Health & Sefety

Vetoseal XX772 should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well-ventilated areas. In case of insufficient ventilation, wear suitable respiratory protection.

Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection.

Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water.

In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

If swallowed, seek medical attention immediately - do not induce vomiting.

Vetoseal XX772 is flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof EC720

Non-toxic solvent-free epoxy waterproof wall, floor & tank coating

Vetoproof EC760

Two-component coal tar solvent epoxy protective coating

Vetoproof EC761

Solvent-free coal tar epoxy-based protective coating

Vetoproof EC722

Epoxy Polysulphide Elastomeric Coating System

Vetoseal XW770
Silicone-based polymeric water repellant pore sealer & hardener for limestone, masonry & natural stone

">

Silicone-based polymeric water repellant pore sealer & hardener for limestone, masonry & natural stone

view more
Featured Product
Vetoprime EP491

Versatile solvent free epoxy based primer

Uses
As a universal versatile primer for resinous flooring and concrete repair systems, especially screeds and self smoothening toppings.
As a stand-alone sealer and surface hardener.
As a dust proofer for cementitious surfaces.
Sealing of highly porous cementitious substrates.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com