Accessories
Vetoflex PBR

Closed-cell polyethylene backing rod

Uses
Controlling and filling gaps behind sealants.
Prohibiting sealant bonding to joint fillers.
Allowing joint sealant freedom of movement to achieve its desired function.
Fast Download
Technical Data Sheet
download (*.pdf 0.18Mb)
Method Statement
download (*.pdf 0.23Mb)
Technical Information
Product Description

Vetoflex PBR is a closed-cell polyethylene foam cord with minimal water absorption for sizing static and dynamic joints in the building industry. Available in different sizes that range from 6mm to 50mm in diameter and could be applied vertically and horizontally. Vetoflex PBR serves as excellent support for elastomeric sealants and efficient backup material for joint sealing applications.

Advantages
  • Easy to install (can be inserted exerting minor pressure into any joint).
  • Superior resistance from deterioration.
  • Exceptionally flexible.
  • Non-absorbent.
  • Acts as bond breaker with minimum strain shape for joint sealants.
  • Provides firm backing for sealant tooling.
  • Withstands adverse weather conditions.
  • Economical.
Packaging & Coverage

Vetoflex PBR Rod Diameter

(mm)

Piece Length (m) x Pack

 

Quantity / Pack

 

6mm 100mx8pcs 800m
8mm 100mx8pcs 800m
10mm 100mx8pcs 800m
12mm 100mx8pcs 800m
15mm 60mx6pcs 360m
20mm 50mx4pcs 200m
25mm 25mx4pcs 100m
30mm 25mx4pcs 100m
40mm 4mx25pcs 100m
50mm 4mx25pcs 100m
60mm 4mx25pcs 100m
Shelf Life & Storage

Keep Vetoflex PBR stored clear of ground in a dry, shaded place below 35ºC.

Application Information
Instructions for use

Application

Cut Vetoflex PBR according to the required length and lay it along the joints accordingly. Next, gently push the cord against the joint with extra caution not to damage the skin of the material.

Ensure that the diameter of Vetoflex PBR is approximately 20% to 25% (required depth to width ratio) greater than the joint's width to ensure that the cord is tightly held in position. This procedure further enhances the aesthetic effect of the material when done on a firm base. Next, seal the joint with a suitable sealant from Saveto’s product range.

Surface Preparation

All surfaces where the backing rod is to be inserted must be dry, smooth, clean, free from dust, laitance, or loose materials. When otherwise necessary, it is highly recommended to use compressed air or a wire brush in order to remove further dirt, oil stains, and other inconsistencies.

Additional Information
Health & Sefety

Vetoflex PBR is not classified as hazardous.
Vetoflex PBR is a combustible product. Avoid any exposure to all sources of ignition or flame.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetonit PAB100

Saveto plaster accessories  - plaster architrave beads

Vetonit PAB500

Saveto plaster accessories - angle beads

Vetonit PBL

Saveto block reinforcement access-ories ladder type

 

Vetonit PCJ

Saveto plaster accessories - plaster control joint 

 

Vetonit PCL

Saveto plaster accessories - plaster coil lath 

 

view more
Featured Product
Masonry Grout Filler

Premixed cementitious masonry grout

Uses
Apply Masonry Grout Filler on cement-based masonry blocks, masonry units, behind marble and cement panels, tiles or slabs, etc.
Masonry Grout Filler is suitable for the application behind gypsum boards.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com