Flooring Systems
Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed

Uses
Leveling of concrete slabs before the application of final floor coverings.
Screeding over hollow-core pre-cast concrete slabs.
Leveling floors and slabs to slope to ensure proper flow to drains.
Fast Download
Catalogues
Saveto Flooring Technical Guide
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop CS536 is a single component cementitious floor screed composed of hydraulic binders, silica sand, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site; once mixed, it will form a  trowelable screed mortar applied in thicknesses between 30 and 100 mm.

Advantages
  • Factory-controlled pre-blend ensures consistently high quality.
  • Suitable for Middle East harsh weather conditions.
  • Easy application enabling high productivity & superior finishing.
  • High bond to the substrate.
  • Excellent physical and mechanical properties.
  • Shrinkage compensated.
  • Excellent workability.
COMPLIANCE STANDARD
  • EN197: 2011
  • EN13813:2002
  • BS8204:2010
  • ASTM C109
Packaging & Coverage

Vetotop CS536 is supplied in a 50kg bag.

Yield: 21.7 - 27.8 Ltr.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

 

Shelf Life & Storage

The original sealed bag of Vetotop CS536 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place, at temperatures between 5ºC - 35ºC.

Colors
Grey Colour
Application Information
Instructions for use

Mixing

For the mixture’s preparation, pour into a container 5-6 liters of water for each 50Kg bag of Vetotop CS536.

Add the powder to the water and mix with a low-speed electric drill fitted with a suitable paddle until achieving a uniform, lump-free consistency mix. Do not add further water to the mix. Do not add water to the mix once it starts to set.

Application

Pour the mixed material onto the surface and spread it to the desired thickness using a steel trowel or suitable tools. Cover the Vetotop CS536 with a plastic sheet to avoid drying.

Curing

Cure the screed as per standard concrete curing practices. Do not subject the screed to vehicular traffic for 28 days till ensuring full cure and the system’s ability to withstand designed traffic loads.

If a concrete sealer requires enhancing the screed durability and resistance to water ingress, apply Vetoseal XW770 at a rate of 8 to 12 m2 per liter. Make sure to apply the sealer uniformly and to cover all screed surfaces.

Cleaning

Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.

Surface Preparation

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Priming

Vetotop CS536 can be laid as a bonded screed by applying Vetobond PB434 slurry to the prepared concrete substrate as a bonding and priming layer.

Alternatively, an epoxy bonding agent can be used, such as Vetobond EB430 or Vetobond EB431.

To prepare the slurry primer, mix 1 volume of Vetobond PB434 to 1 volume of clean water with 3 volumes of fresh cement and mix until achieving a smooth consistency. Scrub the mixed slurry into the concrete surface. While the slurry is wet, apply Vetotop CS536 to ensure good adhesion with the substrate.

Limitation
  • Do not apply the product at a temperature of less than +5ºC.
  • Vetotop CS536 should be checked for its suitability when concrete is steam cured. Also, carry out prior tests for its suitability when gypsum or colored mixes are being used.
  • For further information contact our technical department.
Additional Information
Health & Sefety

Vetotop CS536 is highly alkaline; therefore, avoid direct contact with eyes or skin. Vetobond PB434 is a latex emulsion. It is recommended to use protective gloves and goggles during application.

Any skin contact should be washed with plenty amount of water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Vetotop CS536 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

 

More Products from this section
Vetodeck UD
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

">

Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

Vetograin Range
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

">

Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

Vetotop CL530
Premixed 2 to 10 mm thick cementitious self-leveling underlayment

">

Premixed 2 to 10 mm thick cementitious self-leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed

Vetotop EC493
Solvent-based high performance, self-priming, thin epoxy topping

">

Solvent-based high performance, self-priming, thin epoxy topping

view more
Featured Product
Vetocrete FC803
High strength structural fine shotcrete

">

High strength structural fine shotcrete

Uses
It is ideal for large vertical and overhead structural repairs.
It is used for supporting columns and beams.
It is ideal for new construction projects.
Ideal for polystyrene sandwiching and paneling.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com