Flooring Systems
Vetotop UC370

UV resistant trafficable polyurethane coating

Long-term protection of car parks and floors in factories, warehouses, laboratories, loading decks ramps, showers, kitchens, dairies, breweries.
UV Resistant top coat over flooring systems including concrete, epoxies, aromatic polyurethanes,...etc.
Fast Download
Saveto Flooring Technical Guide
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop UC370 is a two-component, low viscosity acrylic urethane topcoat. It is used as UV resistant sealer over concrete and the range of VetoFloor epoxy and polyurethane flooring & coating systems. Vetotop UC370 is recommended as a topcoat for steel substrates after the mandatory priming by Vetoprime EP390. Vetotop UC370 is UV stable for exterior applications, cures rapidly, and the sealed system is ideal for all-weather exposure. Vetotop UC370 gives a hard, glossy surface that offers excellent stain resistance and easy cleanability when used as a finish coat. Vetotop UC370 is supplied in a pack size of 4 & 15 liters kit consist of Resin & Hardener.

  • Excellent adhesion.
  • UV Resistant - does not yellow.
  • Durable and low maintenance cost.
  • Good resistance to a wide range of chemicals.
  • High mechanical properties with excellent impact and abrasion resistance.
  • Provides a degree of Flexibility.
  • BS 7976-2
  • ASTM D 638
  • BS 3900
Packaging & Coverage

Vetotop UC370 is supplied in 4 & 15 Liters Kit. Theoretical Coverage - 7 m2/Liter.

Vetoprime EP491 supplied in 4 Liters Kit. Theoretical Coverage - 8 m2/Liter.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

In the case of using antislip aggregates, the consumption values for the topcoat will increase by 15 - 40%.


Shelf Life & Storage

The original sealed kit of Vetotop UC370 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Mixing Vetotop UC370

In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied, ensuring that all containers are scraped clean. Do not add solvent thinners at any time.


Apply Vetotop UC370 by roller or airless spray to the surface. Spray Vetotop UC370 at a thickness of 125-150 micron (50% solids), so the application coverage rate should be at 7 m2/liter per coat.

The application should not be carried out when humidity exceeds 85% or when the surface temperature to be coated less than 3°C above the dew point.

Vetotop UC370 can be applied as a single coat or multi-coat sandwich system incorporating Vetograin products to give a slip-resistant finish.

For more information, please refer to the Vetograin Technical Data Sheet.

Re-coating time is 24h max if temp >25°C.

Expansion Joints

Expansion joints in the existing substrate must be retained and continued through the Vetotop UC370 topping. Saveto has a range of joint sealants specifically designed for flooring (see Vetoflex PS782 product data sheet).


Clean tools and equipment with Vetonit Solvent XX300 immediately after use.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. Repair all necessary areas before application by using epoxy mortar from the Vetorep ER range.

New concrete floors shall be at least 28 days old with a moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).


Design Criteria

Vetotop UC370 is designed to be applied by roller or airless spray in two or more coats at a thickness of 100 microns per coat (DFT). The product is designed to resist ultraviolet rays (UV) while being trafficable and abrasion-resistant.

Additional Information
Health & Sefety

Vetotop UC370 is irritant and harmful; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice.
Ensure adequate ventilation when using a product or when using a solvent for cleaning purposes and avoid inhalation of vapors.
The use of barrier creams provides additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetotop UC370 and Vetonit Solvent XX300 are flammable. Keep away from sources of ignition. No Smoking. In the event of a fire, extinguish with CO2 or foam.
Refer to the product(s) MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly, arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system


Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

Vetograin Range
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system


Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

Vetotop CL530
Premixed 2 to 10 mm thick cementitious self-leveling underlayment


Premixed 2 to 10 mm thick cementitious self-leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed

view more
Featured Product
Vetoproof S

Elastomeric crack-bridging cementitious waterproof membrane


Waterproof lining for swimming pools (under tiling), water tanks, canals,...etc.
Wet-areas waterproofing while receiving Saveto tile adhesives.
Protecting concrete and masonry structures against ingress of chloride ions and carbonation.
Negative hydrostatic pressure resistance.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com