Flooring Systems
Vetotop UL171

Medium duty polyurethane hybrid flooring system

Where maximum flooring chemical resistance is required in food and beverage productions, pharmaceutical production, and chemical plants.
Where smooth, even, and easy to clean surface is required, such as in Textile and film plants, warehousing and storage, confectionery production, electronic component manufacture & assembly.
Fast Download
Technical Information
Product Description

Vetotop UL171 is a single-layer, seamless, solvent-free, polyurethane flooring system with a smooth matt surface finish. It has high impact resistance and withstands abrasive wear and a wide spectrum of chemicals. The product is a 3 component system consisting of a base, hardener, and powder filler.

  • Low maintenance cost.
  • Hygienic, impervious, and easily cleanable.
  • Available in 6 standard colors.
  • High bond, stronger than concrete cohesive strength.
  • BS 476-7-1997 as class 2 in flame spread.
  • DIN 53457
Packaging & Coverage

Vetotop UL171 is supplied in a 28kg Kit. Theoretical coverage: 1.9 kg/m2 @ 1mm thickness.

Vetoprime UP170 is supplied in a 3kg Kit. Theoretical coverage: 10 m2/3kg kit.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed kit of Vetotop UL171 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 25ºC.

Application Information
Instructions for use

Design Criteria

Vetotop UL171 is designed to be a hard-wearing self smoothening single pour application on cementitious or metal substrates at thicknesses between 3 to 6 mm. The applied product will be resistant to water as well as a wide range of chemicals.


All surfaces receiving Vetotop UL171 should be primed with Vetoprime UP170, designed for maximum absorption and adhesion to concrete substrates or applied over a 1mm “scratch coat” Vetotop UL171. Add the entire content of the hardener tin to the base tin and mix the two primer components thoroughly for at least 2 minutes - only mix full packs. Once mixed, apply the primer immediately to the prepared substrate using stiff brushes and/or rollers. The primer should be well ‘scrubbed’ into the substrate to ensure full coverage, but take care to avoid over-application or ‘ponding.’ Allow the primer to dry before proceeding to the next stage, do not proceed whilst the primer is ‘tacky’ as this will lead to unsightly marks in the finished surface. Porous substrates may require a second primer coat - when the first coat is directly absorbed into the substrate - but still, observe minimum over-coating times.


Vetotop UL171 is supplied in three pre-weighed packs (base, hardener, and aggregate), ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both the performance and the finished floor's appearance. Mix using either a forced action mixer or a heavy-duty mobile mixer fitted with a jiffy-type mixing paddle. All such equipment should be of a type and capacity approved by Saveto. Mix the components in a suitably sized mixing vessel. Stir the base and hardener components individually, then empty them into the mixing vessel scrapping the edges and mix for 30 seconds. Slowly, add the content of the graded aggregate pack and mix for a further 3 minutes until obtaining a completely homogeneous material.


Optimum application temperature to achieve the best flow and leveling qualities is done at 25-30ºC; However, the UL171 can be applied at temperatures of 20-32ºC. Ensure sufficient labor and materials to make the mixing and subsequent application process a continuous one for any given, independent floor area. Once mixed, use the material within its specified pot life. Pour the material onto the prepared and primed substrate as soon as mixing is complete. Spread it to the required thickness using a notched trowel or a gauged spreader, with care taken not to overwork the resin, spreading evenly and slowly. After laying, roll the material immediately, using a spiked nylon roller to remove slight trowel marks and assist air release. Use a ‘back and forth’ technique along the same path for rolling. An overlap of 50% with adjacent paths is recommended. Further light rolling may be required to remove surface imperfections or for subsequent release of trapped air but should be before the setting of the product.

Floor Joints

Follow all existing expansion or movement joints through the new floor surface.


Remove Vetoprime UP170 and Vetotop UL171 from tools and equipment with water immediately after use. Remove hardened material mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. All necessary repairs should be made before application by using Vetotop US172.  New concrete floors shall be at least 5 days old and visibly dry without standing water on top. Cut the grooves according to the floor area to control shrinkage. Please contact Saveto for information.

Additional Information
Health & Sefety

Vetotop UL171 is irritant and harmful; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice. Ensure adequate ventilation when using the product. In case of contact with skin or eyes, rinse with plenty of clean water and seek medical advice. Keep away from sources of ignition. No Smoking. In the event of fire extinguish with CO₂ or foam.

Refer to product(s) MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly, arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system


Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

Vetograin Range
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system


Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

Vetotop CL530
Premixed 2 to 10 mm thick cementitious self-leveling underlayment


Premixed 2 to 10 mm thick cementitious self-leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed

view more
Featured Product
Vetotouch Serene

Cementitious polymer modified decorative finish coat applied at thicknesses from 1 to 3mm

External and internal building facades.
As a finish coat for EIFS / ETICS systems.
On plastered walls, fair-faced concrete substrates, and pre-cast panels.
Decorative effects: marble finish and special effects.
Micro-concrete finish decorative effect.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com