Flooring Systems
Vetotop US172

Heavy-duty polyurethane hybrid flooring system

Mechanical and chemical exposure applications.
Laboratories, food and Beverage industries, dairies, cheese and milk production, meat, fish, and poultry processing.
Commercial and industrial kitchens
Freezer rooms and applications where thermal shock resistance is required.
Fast Download
Technical Information
Product Description

Vetotop US172 is a single-layer, seamless, solvent-free, polyurethane-based flooring system. Its textured matt finish possesses excellent chemical resistance, withstands abrasive wear, has high impact resistance, and withstands direct steam contact and cleaning practices.

  • Thermal shock resistance.
  • High abrasion and chemical resistance.
  • Low maintenance cost.
  • Hygienic, impervious, and easily cleanable.
  • High bond, stronger than concrete cohesive strength.
  • BS EN476:2009 as class 2 in flame spread.
  • ASTM D4364-13 weathering resistance.
  • ASTM D2485-91(2013) high service temparature operation.
Packaging & Coverage

Vetotop US172 is supplied in a 30kg Kit.

Coverage: 2.1-2.3 kg m2 @ 1mm thickness.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed kit of Vetotop US172 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 30ºC.

Application Information
Instructions for use

Design Criteria

Vetotop US172 is designed to be a hard-wearing trowel-applied polyurethane screed on cementitious or metal substrates at thicknesses 6, 9, or 12 mm. The applied product will be resistant to water as well as a wide range of chemicals.


All surfaces receiving Vetotop US172 can be applied directly to sound and non-porous concrete.


Vetotop US172 is supplied in three pre-weighed packs (base, hardener, and aggregate), ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both the performance and the finished floor's appearance. Mixing should be carried out using either a forced action mixer or a heavy-duty mobile mixer fitted with a suitable jiffy-type mixing paddle. All such equipment should be of a type and capacity approved by Saveto. Mix the components in a suitably sized mixing vessel. Stir the base and hardener components individually, then empty them into the mixing vessel scrapping the edges and mix for 2 minutes. Slowly, add the content of the graded aggregate pack and mix for a further 3 minutes until obtaining a completely homogeneous material.


Spread Vetotop US172 to a uniform thickness on the primed surface using either a screed box or the edge of a steel trowel. Tamp the material with a wooden float to ensure complete compaction. Finally, finish to a closed even texture using a steel trowel. Screeding rods are useful to maintain a minimum compacted thickness of 6mm. Apply the material within the pot life after mixing.


Although Vetotop US172 is impervious at 6mm thick in constantly wet operations areas or where a high degree of cleanliness is required.


Clean all tools and equipment immediately after use with water.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. All necessary repairs should be made before the application by using the same material. New concrete floors shall be at least 5 days old and visibly dry with no standing water on top.

Grooves must be cut in concrete to control shrinkage. Please contact Saveto for further advice. 

Additional Information
Health & Sefety

Vetotop US172 should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well-ventilated areas. In case of insufficient ventilation, wear suitable respiratory protection. Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection.
Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.
Refer to product MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system


Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

Vetograin Range
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system


Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

Vetotop CL530
Premixed 2 to 10 mm thick cementitious self-leveling underlayment


Premixed 2 to 10 mm thick cementitious self-leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed

view more
Featured Product
Vetocure XT427

Water-based acrylic curing compound and primer *

As a spray-applied membrane for interior application on concrete surfaces and renders.
In situations where the surfaces need to be painted or plastered.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com