Tiling Systems
Vetoset CA544

Specialty polymer modified cementitious adhesive for glass blocks and glass mosaic tiles

As an adhesive for glass block.
As an adhesive for glass mosaic tiles.
Internal and external applications.
Fast Download
Saveto Tile Adhesives & Grouts Professional Product Range Brochure
download (*.pdf 2.34Mb)
Technical Information
Product Description

Vetoset CA544 is a special mortar composed of high-performance hydraulic binders, synthetic resins, carefully selected fillers, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which only requires clean water to produce a creamy paste with thixotropic properties. Vetoset CA544 is specially formulated for sealing glass blocks and the installation of glass tiles. Vetoset CA544 does not contain asbestos fiber or other toxic materials.

  • Single component, it requires only addition of water, easy to mix & apply.

  • Excellent physical & mechanical properties. 

  • Water-resistant. 

  • Excellent resistance to yellowing.

  • Suitable for interior & exterior applications. 

  • Excellent resistance to staining.

  • BS:EN 12004 as type C2TE S1
  • SASO ISO 13007-1 as type C2TE S1
Packaging & Coverage

Vetoset CA544 is supplied in 20kg Bags.

Yield: 16 Liters

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastages.

Shelf Life & Storage

The original sealed bag of Vetoset CA544 has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

White Powder
Application Information
Instructions for use


For the preparation of mortar adhesive, pour into a container 5.6- 6.4 liters of water for each 20kg bag of Vetoset CA544. Add the powder to the water and mix with a low-speed electric drill fitted with a suitable paddle for 4-5 minutes until achieving a uniform, lump-free consistency. Allow the mixed material to stand for about 10 minutes and remix briefly without adding further water.

Blend Premium Project Fix manually for small quantities and maintain the correct amount of powder to water.

Use the mixed material within 60 minutes at 25 degrees.

Do not try to remix or add water to the mixture once the mortar adhesive starts to harden.


Apply Vetoset CA544 with a trowel, then position the glass blocks in the opening. Use a special molder to verify the glass block alignment. Remove the excess mortar before it hardens.

For Gap filling, compact the mixture by using a smooth rubber spatula. Let the product harden for about 10 minutes; after that, clean the surface using a damp sponge. When the product is well hardened, clean it with a dry cloth.


Clean tools and equipment with water immediately after use. Remove the hardened material using mechanical means.

Surface Preparation

The surface should be sound, clean, free from loose material, etc. Level the horizontal surfaces and ensure that the vertical sides are perfectly plumb-in or secured to guarantee a perfect glass block alignment. The support must be solid, compact, free from loose parts, dust, and greasy substances.


Additional Information
Health & Sefety

Vetoset CA544 is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Vetoset CA544 is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ceramic Tile Fix

Weather-resistant cementitious adhesive for ceramic tiles

Pool FIX

Polymer modified water resistant adhesive for fixing swimming pools, fountains & water tanks tiles


Pool Grout

Water-resistant grout for swimming pool tile joints

Porcelain Tile Fix

Polymer modified weather resistant adhesive for porcelain tiles.

Premium Project Fix

High quality ceramic tile adhesive for projects.


view more
Featured Product
Vetonit Base WR EG

Weather Resistant Premix Cement Coating for External Use

It can be applied externally onto walls & other surfaces subjected from dry to humid conditions
Suitable for applications on concrete surfaces and precast concrete surfaces.
On-wall surfaces that are plastered with water-resistant plasters, Vetonit Renders, and on damp concrete interiors.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com