Vetoproof AM763

Single component acrylic waterproofing membrane

Waterproofing of concrete, asbestos, cement, and gypsum board surfaces.
Protecting spray-PU membranes from UV rays.
As a decorative overlay on bituminous membranes and over existing terrazzo tiles.
Fast Download
Technical Information
Product Description

Vetoproof AM763 is a single component elastomeric water-based acrylic membrane that has versatile uses for waterproofing in residential and commercial construction. The product is available in white.

  • Flexible elastomeric product.
  • Easy to use single component.
  • Weather-resistant.
  • It can be applied over sloped roofs.
  • Easy to maintain.
Packaging & Coverage

Vetoproof AM763 is supplied in 20kg Pails.

Theoretical Coverage 0.7-1.0 kg/m2/coat.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Vetoproof AM763 and has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Application Information
Instructions for use


Apply Vetoproof AM763 with a brush, roll, or airless spray machine. Prime Porous cementitious surfaces with Vetoprime AP443. Apply the first coat of Vetoproof AM763 at the rate of 1.5 - 2.0 m²/kg and allow it to cure for 4 - 12 hours depending on the ambient temperature.

Apply the second coat perpendicular to the first coat at the same rate above and allow it to cure.

It is recommended for heavy pedestrian traffic to use fiberglass scrim reinforcement, embedded firmly in the second coat while wet, and a third coat should be applied.


Remove Vetoproof AM763 product from tools, equipment, and mixers with clean water before the initial set. Cured material can only be removed mechanically.

Surface Preparation

All surfaces should be dry and free from contamination, such as oil, grease, loose particles, decayed matter, moss algal growth, laitance, and all traces of mold release oils and curing compounds. This is best achieved by lightly grit-blasting the surface. Where moss, algae, or similar growths have occurred, treatment with a proprietary biocide should be carried out after the grit-blasting process. Spalled and deeply disintegrated concrete should be removed to sound concrete and repaired with a Saveto repair system.

Concrete substrates should be at least 14 days old; bituminous substrates should be at least 12 months old before overcoating with Vetoproof AM763.

  • Vetoproof AM763 should not be applied at ambient temperatures below 5°C and dropping.
  • Vetoproof AM763 should not be applied on surfaces expected to suffer from rising dampness or relative humidity greater than 75%.
  • Being Styrene Acrylic, Vetoproof AM763 may yellow over time from UV rays, but the membrane's integrity and function are not compromised.
  • If any doubts arise concerning application or substrate conditions, consult the Saveto office.
Additional Information
Health & Sefety

Vetoproof AM763 contains an acrylic polymer that can be harmful to the skin. During use, avoid contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection, and respiratory protective equipment. The use of barrier cream provides additional skin protection. In case of skin contact, rinse with plenty of clean water, cleanse with soap and water. In case of contact with the eye, rinse immediately
with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.

Vetoproof AM763 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Cool Top
Single component flexible hybrid roof water proofing membrane


Single component flexible hybrid roof water proofing membrane

Vetoproof CM740

Single component elastomeric crack-bridging cementitious waterproof membrane

Vetoproof AM764

Single component flexible pure acrylic waterproofing membrane

Vetoproof CM744

Polymer modified water resistant cementitious top coat

Vetoproof CM741

Single component penetrating waterproofing system for concrete

view more
Featured Product
Vetodeck UD
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system


Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

Heavily trafficked areas.
Car park decks, car park ramps.
Turning areas, entrances, and thoroughfares.
On the new and existing floor.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com