Flooring Systems
Vetotop UC363

High performance, aromatic & flexible waterproof polyurethane flooring membrane

Uses
Carpark decks.
Food and pharmaceutical industry flooring.
Aircraft hangers.
Service centers, workshops.
Fast Download
Technical Information
Product Description

Vetotop UC363 is a two-component, solvent-free aromatic polyurethane intermediate coat and waterproofing membrane. The product needs to be overcoated with Vetotop UC370 or Vetotop UC371 for optimum performance and scratch resistance. The product's flexibility enables it to perform in a wide range of flooring applications.

Advantages
  • Fast, easy application.
  • Flexible.
  • Low maintenance cost.
  • Hygienic, impervious, and easily cleanable.
  • High bond, stronger than concrete cohesive strength.
  • Excellent impact resistance.
COMPLIANCE STANDARD
  • ASTM D 6577-15
  • BS EN476:2009 as class 1 in flame spread.
Packaging & Coverage

Vetotop UC363 is supplied in 4 or 15 Liters Kit with Theoretical coverage:1.25 m2/Liter.

Vetoprime UP360 is supplied in 4  Liters Kit with Theoretical coverage: 8-10 m2/Liter.

Vetoprime EP490 is supplied in 4  Liters Kit with Theoretical coverage: 8-10 m2/Liter.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

In the case of using antislip aggregates, the consumption values for the topcoat will increase by 15 - 20%.

 

Shelf Life & Storage

The original sealed kit of Vetotop UC363 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Priming

Prime concrete substrates with Vetoprime UP360 or Vetoprime EP490.

Mixing Vetotop UC363

In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied, ensuring that all containers are scraped clean. Do not add solvent thinners at any time.

Application

Apply Vetotop UC363 by a pin leveler or airless spray to the dry surface. The application should be at a rate of 1.25 m2/liter per coat.

The application should not be carried out when relative humidity exceeds 75% or when the surface temperature to be coated less than 3°C above the dew point.

Vetotop UC363 can be applied as a single coat or dressed with Vetograin products to give a slip-resistant finish.

For more information, please refer to Vetograin Technical Data Sheet.

Expansion Joints

Expansion joints in the existing substrate must be retained and continued through the Vetotop UC363 topping. Saveto has a range of joint sealants specifically designed for flooring (see Vetoflex PS782 product data sheet).

 

Cleaning

Clean tools and equipment with Vetonit Solvent XX300 immediately after use.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. Repair all necessary surfaces before application by using epoxy mortar from the Vetorep ER range. New concrete floors shall be at least 28 days old with a moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Additional Information
Health & Sefety

Vetotop UC363 is irritant and harmful; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice.

Ensure adequate ventilation when using the product or when using solvent for cleaning purposes and avoid inhalation of vapors. The use of barrier creams provides additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetonit Solvent XX300 is flammable. Keep away from sources of ignition. No Smoking. In the event of a fire, extinguish with CO2 or foam. Refer to the product(s) MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetodeck UD
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

">

Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

Vetograin Range
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

">

Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

Vetotop CL530
Premixed 2 to 10 mm thick cementitious self-leveling underlayment

">

Premixed 2 to 10 mm thick cementitious self-leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed

view more
Featured Product
Vetoseal XW771
Waterbased nonstaining siloxane  water repellant

">

Waterbased nonstaining siloxane  water repellant

Uses
Transforming construction substrates to water-repelling surfaces.
Cementitious substrates: block and brickwork, pre-cast panels, and plasters.
Sealing and treatment natural stone, marble, and absorbent tiles.
As a sealer for cementitious-based Vetotouch range of EIFS/ETICS finishes.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com