Renders & Finishes
Vetonit Base WR EG

Weather Resistant Premix Cement Coating for External Use

Uses
It can be applied externally onto walls & other surfaces subjected from dry to humid conditions
Suitable for applications on concrete surfaces and precast concrete surfaces.
On-wall surfaces that are plastered with water-resistant plasters, Vetonit Renders, and on damp concrete interiors.
Fast Download
Technical Information
Product Description

Vetonit Base WR EG is a cement-based coat composed of hydraulic binders, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which required only the addition of clean water to produce easily workable mortar. Vetonit Base WR EG is a high-quality product for multipurpose use and a base coat for Vetonit Finish WR EG. Vetonit Base WR EG can be applied in thickness from 1 mm to 5 mm, in one or two layers depending on the on-site requirement. Vetonit Base WR EG is available in two standard colors, white, grey & Saveto standard colors.

Advantages
  • Factory controlled pre-blend ensures consistently high quality.
  • Requires only the addition of water on-site at the time of usage.
  • Manual or spray machine application.
  • Superior workability.
  • Easy application that enables high productivity.
  • Excellent Adhesion on a variety of substrates.
  • Water/weather resistant.
  • Suitable for humid & dry conditions.
  • Suitable for walls & precast surfaces.
  • Guards the surfaces from rain & natural condensations.
COMPLIANCE STANDARD
  • BS:EN 1015
  • ASTM C348 
  • ASTM C109
  • BSEN 998-1
  • BS:EN 413-2 
Packaging & Coverage

Vetonit Base WR EG is supplied in a 25kg Bag or Bulk.

Yield: 1.0 - 1.2 Kg /m2 / 1mm thickness.

Stated consumption data are for general guidance. Actual value depends on the nature of the substrate, method of application & wastages.

Shelf Life & Storage

The original sealed bag of Vetonit Base WR EG has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place.

Colors
White, Grey & colored Powder
Application Information
Instructions for use

Mixing

Internal Block Walls & Rough Surfaces

For manual application, add to the mixing container 7.5-8.5 liters of water for each 25 Kg bag of Vetonit Base WR EG. For the Spray machine application, use 9.5-10.0 liters of water for each 25 kg bag. Add the powder to the water and mix with a mechanical mixer, or use a low-speed electric drill fitted with a suitable paddle. Mix for 3-4 minutes until achieving a uniform, lump-free consistency. Allow the mixed material to stand for about 10 minutes, and remix briefly without adding further water.

Smooth Concrete Surfaces

Add 0.5 liters of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow the same mixing procedure as described above.

Use the mixed material within 4 hours. Do not add water to the mix once the mixed mortar starts to harden.

Application

Apply Vetonit Base WR EG to achieve a maximum thickness of 5 mm in layers, 1-2 mm per layer.

To obtain different finish textures, select the appropriate gun nozzle size, or vary the spraying distance.

Do not disturb the installed material for at least 48 hours.

Curing

Cure Vetonit Base WR EG by spraying the applied material’s surface with water every 12 hrs for a minimum of 3 days. During hot & dry conditions, allow curing for a minimum of 5 days. This will help achieve a uniform color, minimize the risk of surface cracks, and lead to higher mechanical strengths.

Cleaning

Clean all tools with water immediately after finishing. Clean hardened materials mechanically.

Surface Preparation

The surface should be sound,  clean, free from loose material, grease, laitance, dirt curing compound, etc.

Before the Vetonit Base WR EG application, wet the entire surfaces with clean potable water, and the surface should look damp at the time of the Vetonit Base WR EG application.

Limitation
  • Do not mix with any additives or products unless recommended by Saveto.
  • Make sure the substrate is suitable for the plaster coat application. In case of doubt, try on a sample area to assess its suitability.
  • Do not apply the product at a temperature of less than +5ºC. During the summer season, the working area must be covered to prevent ill-effects from direct sun and excessive air-draught during the initial curing stage.
  • For further information contact our technical department.
Additional Information
Health & Sefety

Vetonit Base WR EG is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eye irritation, immediately washed with a copious amount of clean cold water. Seek medical advice.

Vetonit Base WR EG is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Putty Fine

PVA copolymer based high-quality putty

Vetogyps Compound
Gypsum surfaces skim and finish compound

">

Gypsum surfaces skim and finish compound

Vetonit Crack Filler

High quality premixed surface crack filler

Vetonit Finish WR

Water resistant internal use premix smooth cement coating

Vetonit Finish WR EG

Water-resistant external use premix smooth cement coating

view more
Featured Product
Saveto Cool Top
Single component flexible hybrid roof water proofing membrane

">

Single component flexible hybrid roof water proofing membrane

Uses
Waterproofing of concrete, metal, cement, and gypsum board surfaces.
Protecting bitumen and PVC roofing membranes with a high value of SRI.
Waterproofing of corrugated sheets and sloped roofs.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com