Concrete Repairs & Grouts
Vetoanchor EG346

Epoxy resin twin cartridge anchoring grout

Uses
Anchoring bolts, brickwork, threaded studs, hollow masonry sleeves, threaded inserts, and steel columns into rock, concrete, masonry.
Permanent installation of reinforcement starter bars, foundation bolts, base plates, balustrading, barriers and safety fences, railway tracks, tie-back anchors, reinforcement doweling abutments, ground anchors for towers, cranes, dock sills, etc.
Fast Download
Technical Information
Product Description

Vetoanchor EG346 is a two-component, styrene-free, pure epoxy-based, high-strength adhesive anchoring system. The system includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools, and hole cleaning equipment. The product is designed for bonding threaded rod and reinforcing bar hardware into drilled holes in the concrete base and solid masonry materials. Vetoanchor EG346 is available in two packaging twin cartridge systems: 400 milliliters side-by-side cartridges that require a specifically designed injection gun.

Advantages
  • High grip force, high adhesive force.
  • Designed for use with threaded rod and reinforcing bar hardware elements.
  • Special application to diamond drilled holes and large bore diameter.
  • The product ingredients are odorless and non-toxic.
  • Wide application temperature range (0 - 40 ºC).
  • Styrene free.
  • Rapid strength gain.
  • Cost-effective.
  • Excellent physical and mechanical properties.
Packaging & Coverage

Vetoanchor EG346 is supplied in 400 ml twin cartridge sets.

 

Shelf Life & Storage

The Original sealed cartridge of Vetoanchor EG346 has a shelf life of 18 months, provided it is stored clear of ground in a dry and shaded temperature-controlled place less than 35ºC.

Colors
Grey
Application Information
Instructions for use

Application

Open the cartridge and remove the red stopper on top. Use Good nozzles after removing the red stopper from the cartridge, and attach the mixing nozzles screwing down tightly. Assemble cartridge into the caulking gun and dispense 2-3 trigger pulls of adhesive to waste until grey color appears with no streaks.

Open the valve and squeeze the handle, so the material is dispensed out of the nozzle until an even, uniform grey color is achieved. Before a new cartridge is introduced into the hole, dispense the first 10 ml or so to waste until the mix is even on color. Initial flow should be disposed of into empty packaging or similar materials. Inject resin into the hole, starting from the bottom of the hole. The material must be injected without creating air pockets.

Insert studs or anchors by pushing the stud into the hole using a slow twisting motion. Wipe away the excess material. Anchor or stud needs to be clean and oil-free. Do not touch studs or anchor until the mixture gels. Do not load the anchor until curing is completed as per the curing timetable.

Surface Preparation

Hole preparation

The optimum performance of Vetoanchor EG346 grouts requires rough-sided, dust-free holes. It is recommended to use rotary percussive drills with air pressure.

Diamond drilled holes should be under-reamed.

Cast holes should preferably be inverse dovetail configuration. If parallel-sided holes are cast, they should be rough to provide adequate keying.

Brushing the holes and air blowing is a must for all holes; the concrete needs to be dry with a relative humidity of less than 75% before application.

Limitation

Design Criteria

The high strength of the cured resin permits strong anchors to be created. Ultimate strength is varied by:

  • Strength of host material.
  • Length of resin bond to bar.
  • Hole preparation and formation.
  • Type and dimension of the bar.

Check the attached tables for more information.

Limitation

  • Do not install anchors when the substrate temperature is less than 0°C.
  • Do not install anchors when Vetoanchor EG346 temperature is less than 15°C.
  • AT temperatures below 15°C, the product should be warmed or stored in temperatures of 15-30°C for 24 hours before use to improve product flow and cure.
  • If the gelling time is superseded, use a new static mixer.
  • Do not cut or shorten nozzles.
  • If the cartridge is not finished, clean the opening, then put the plug back and cap tightly. To use the cartridge set again, replace the static mixer.
  • Do not dilute the material with any solvents and/or other chemicals.
  • Not suitable for use in diamond-cored holes without roughening.
  • Please ensure the spiral mixer in nozzles.
  • Do not install into uncured concrete.
  • Use Good Use nozzles; other nozzles may cause ineffective mixing and adversely affect the material.
Additional Information
Health & Sefety

Avoid contact with the skin as certain sensitive skins may be affected if contacted with epoxy resin. In case of resin contact, wash the skin immediately with soap and water - do not use solvent.

When handling these products, wear gloves and use barrier creams.

Wash eye contamination immediately with plenty of water, and seek medical treatment.

Vetoanchor EG346 is not Flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly, arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetocrete FC803
High strength structural fine shotcrete

">

High strength structural fine shotcrete

Vetocrete CC806
High strength structural shotcrete

">

High strength structural shotcrete

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

Vetogrout CG513
Free-flowing pre-bagged non-shrink cementitious cable grout

">

Free-flowing pre-bagged non-shrink cementitious cable grout

Vetogrout CG518
Chloride free nonmetallic non-shrink grout

">

Chloride free nonmetallic non-shrink grout

view more
Featured Product
Vetorep ER430

Pitch extended epoxy based repair compound for asphalt crack repairs

Uses
Repair of asphalt cracks in highways, aprons, and pavements.
Reinstate asphalt integrity while maintaining flexibility.
Road bridges, helicopter decks, work platforms, car parks, walkways, wet work industrial areas, and cargo handling areas.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com