Primers and Ancillary
Saveto Bond 2

Multipurpose low viscosity bonding agent & admixture

Uses
Works as an admixture with plasters, lime/sand cement screeds, renders, mortars, and cement grouts when diluted 1:2 with potable water.
Works as a bonding agent, and it can be sprayed or brushed on green substrates to improve bonding of plasters, patching compounds. For renders, mortars, joint tape fixing, etc., when diluted 2:1 with potable water.
Use for both internal and external applications.
Fast Download
Technical Information
Product Description

Saveto Bond 2 is a single component polymer-based bonding agent for cementitious materials. It is water-based, specially formulated to enhance bonding properties and improve the mechanical strengths of cementitious mixes when incorporated with mixing water. Saveto Bond 2 also reduces shrinkage cracks during the early stages of cement hardening by minimizing surface water loss in freshly applied mixes. Saveto Bond 2 can be diluted on site with potable water for desired applications. Saveto Bond 2 is ideal for use with Premix Plaster.

Advantages
  • Multipurpose usage.
  • It can be used as a bonding agent & admixture.
  • Enhances bonding of plaster, sand/cement screed, renders, etc.
  • Improves hydration & curing when added to cement-based mixes.
  • Improves compression strength & abrasion.
  • It adheres well to various construction materials, including concrete, stone, etc.
  • Ensure brighter & long-lasting color to architectural finishes.
  • Reduces shrinkage & cracks.
COMPLIANCE STANDARD
  • ASTM C932
  • BS 6319
Packaging & Coverage

Saveto Bond 2 is supplied in a 20 Liters Jerrican.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Saveto Bond 2 has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colors
Milky white liquid
Application Information
Instructions for use

Application

Saveto Bond 2 tends to soft settlement on storage, and therefore it is recommended to mix the material in the same container before use.

Follow the dilution ratio required for each type of premixed mortar.

As Admixture

Dilute 1 part Saveto Bond 2 with 2 parts water. Mix thoroughly to obtain uniform consistency liquid.

Add the diluted Saveto Bond 2 to pre-blended sand/cement plaster, mortar, or other dry mixes. Mix for 3-4 min using a mechanical mixer at low speed. Let the mixture stand for 10 min and mix again briefly to achieve a homogeneous lump-free mixture.

As Bonding Agent

Dilute 2 parts Saveto Bond 2 with 1 part water. Mix thoroughly to obtain uniform consistency liquid.

Apply using a brush or spray directly onto the substrate. If using a hand pump, spray at a rate of 15 m2/liter. While the bonding agent is still wet, follow immediately by applying plaster, render, mortars or joint tapes, etc.

Note: Saveto Bond 2 should remain tacky when applying top coat finishes.

Cleaning

Clean tools with water before it hardens. After the hardening, remove its residuals mechanically only.

Surface Preparation

Clean the surface well and free it from loose materials. Eliminate inconsistent parts, varnishes, grease, laitance, algae through sandblasting or brushing before applying Saveto Bond 2.

Limitation

Use the whole material once you opened the pack as the material starts to skin & then dry.

Do not mix with other materials. Do not apply the product at a temperature less than +7ºC.

For further information, contact Saveto Technical Team.

Additional Information
Health & Sefety

Saveto Bond 2 is irritant and harmful; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice.

Ensure adequate ventilation when using the material and avoid inhalation of vapors.

Refer to the product Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly, arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond
Multi-purpose bonding agent & admixture

">

Multi-purpose bonding agent & admixture

Vetobond PB436
Polymeric soil stabilizer

">

Polymeric soil stabilizer

Vetobond PB434
Polymeric bonding agent, waterproof mix enhancer & primer

">

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433
Versatile resin adhesive, cement modifier, bonding agent & sealer

">

Versatile resin adhesive, cement modifier, bonding agent & sealer

Vetobond EB431
Water dispersible epoxy bonding agent to bond old to new concrete

">

Water dispersible epoxy bonding agent to bond old to new concrete

view more
Featured Product
Vetorep CR523

Single component cementitious fairing coat

Uses
Repair of concrete surface blemishes at a thickness from feather edge to 3 mm.
Unification of concrete surface color.
Filling of plaster cracks and concrete hair cracks cosmetically.
Filling blow holes up to 10 mm.
As a final finish in industrial structures such as parking garages, retaining walls,...etc.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com