Primers and Ancillary
Vetoprime AP443

Water-repelling & anti chloride primer for use with Vetotop AC441 anti-carbonation topcoat

Uses
Primer and sealer for anti-carbonation systems.
Enhancing weak lime-stone and masonry surface strengths to receive resinous toppings.
As a dust proofer for cementitious surfaces.
Sealing of highly porous cementitious substrates and durable seal for stamped concrete.
Fast Download
Technical Information
Product Description

Vetoprime AP443 is a multi-grade surface sealer and hardener for concrete, masonry, and natural stone. Vetoprime AP443 versatility allows it to be used in various applications on block and brickwork, concrete, masonry, lime-based elements, cement boards,  mineral plasters, natural and artificial stone conglomerates.

 

Advantages
  • Single-component, easily applied by brush, roller, or spray.
  • Versatile with applications of a large number of coating materials and sealants.
  • Designed for highly porous weak surfaces.
  • High wetting properties.
  • Specifically designed for natural stone present in the MENA region.
  • Cost-effective, suitable for use in MENA region weathering conditions.
Packaging & Coverage

Vetoprime AP443 is supplied in 20 Liters Pail or 200 Liters Drum.

Shelf Life & Storage

The original sealed container of Vetoprime AP443 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.

Colors
Clear
Application Information
Instructions for use

Application Areas

Vetoprime AP443 is used as a penetrating sealer/primer for stone, concrete, and cement-based products. Vetoseal AP443 will reduce/eliminate water and chloride penetration and efflorescence. The sealer is also used to densify weak stone and masonry products.

Application

Ensure that two flood coats (spray, roller, or brush applied) are made at a rate of 0.2 Liters / m2 allowing for a 2-hour interval between coats.

Cleaning

Clean equipment and tools using Vetonit Solvent XX400 immediately after use. If residual material exists or hardens, use mechanical means such as a wire brush to remove residue.

Surface Preparation

The surface must be sound and thoroughly cleaned before Vetoprime AP443 is applied. All loose particles, old mortar, laitance, dirt, paint, etc., must be removed by brushing with a stiff/wire brush or other suitable means. Fungi or Algae should be scoured away using hypochlorite type bleach or proprietary fungicidal solution and then washed with water. Remove all traces of oil and grease with an industrial-grade chemical degreaser or another suitable degreasing agent.

Additional Information
Health & Sefety

Vetoprime AP443 should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well-ventilated areas. In case of insufficient ventilation, wear suitable respiratory protection. Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting. Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond
Multi-purpose bonding agent & admixture

">

Multi-purpose bonding agent & admixture

Saveto Bond 2
Multipurpose low viscosity bonding agent & admixture

">

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436
Polymeric soil stabilizer

">

Polymeric soil stabilizer

Vetobond PB434
Polymeric bonding agent, waterproof mix enhancer & primer

">

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433
Versatile resin adhesive, cement modifier, bonding agent & sealer

">

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Vetoproof UM766

Elastomeric polyurethane liquid applied waterproofing membrane

 

Uses
Wet areas: kitchens, bathrooms, swimming pools,...etc.
Basements, tunnels, subways, and culverts.
Inverted roofs, suspended slabs, balconies.
Tanking systems.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com