Concrete Repairs & Grouts
Vetorep ER430

Pitch extended epoxy based repair compound for asphalt crack repairs

Uses
Repair of asphalt cracks in highways, aprons, and pavements.
Reinstate asphalt integrity while maintaining flexibility.
Road bridges, helicopter decks, work platforms, car parks, walkways, wet work industrial areas, and cargo handling areas.
Fast Download
Technical Information
Product Description

Vetorep ER430 is a two-component epoxy-based thixotropic solvent-free and fast strength development flexible repair compound. Once the kit components are mixed, the product becomes abrasion-resistant and poured into asphalt cracks, where it sets and bonds perfectly to the asphalt substrate.

Advantages
  • Rapid strength development.
  • Chemically resistant.
  • Superior bond to a wide range of substrates.
  • Compatible with most line marking coatings.
  • Abrasion-resistant for heavy-duty applications.
  • Cures in damp conditions.
COMPLIANCE STANDARD
  • EN 13062:2003
  • EN 1504:2013
  • EN1992:2006
Packaging & Coverage

Vetorep ER430 is supplied in 5 liters Kits.

Vetonit Solvent XX400 is supplied in 5 liters Cans.

 

Shelf Life & Storage

The original sealed kit of Vetorep ER430 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded temperature-controlled place less than 35ºC.

Application Information
Instructions for use

Mixing
Take care to thoroughly mix Vetorep ER430 to ensure producing a fully homogeneous flowable mortar. Vetorep ER430 must be mixed mechanically. Stir the hardener and base components thoroughly to disperse any settlement before mixing them together. Empty the entire hardener container's contents into the base container and thoroughly mix for 3 minutes, then empty the mixture into a forced action mixer of adequate capacity. Add the aggregate slowly while the mixer is running and continue mixing for 2 to 3 minutes until all the components are thoroughly blended. Under no circumstances should part packs be used. Facilitate a slow-speed heavy-duty drill fitted with a purpose mixer.

Application
Pour the mixed Vetorep ER430 into the prepared substrate till filling the cracks into place. Allow the material to set for 16 hours at 25ºC before allowing foot traffic and 48 hours before allowing heavy traffic. In case of the ambient temperature of 35ºC vehicular traffic can be allowed at 30 hours.

Low temperature working
Vetorep ER430 can be applied in cold conditions down to 12ºC. The materials should not be applied when the substrate and/or air temperature is 12ºC and falling. At 12ºC static temperature or 12ºC and rising, the application may proceed.
However, it is highly recommended to apply the products at temperatures above 15ºC to dismiss practical application impediments.

High temperature working
At ambient temperatures above 35ºC, Vetorep ER430 will have shorter pot life. Store the material in the shade or an air-conditioned environment and do not apply under direct sunlight.

Cleaning
Remove Vetorep ER430 from tools, equipment, and mixers with Vetonit Solvent XX400 immediately after use.

Surface Preparation

Clean the surface and remove any loose particles; use compressed air for effective cleaning. 

Limitation
  • Vetorep ER430 should not be used when the temperature is below 10ºC and falling.
  • Do not mix part packs under any circumstances.
  • If any doubt arises concerning temperature or substrate condition, consult the local Saveto office.
Additional Information
Health & Sefety

Vetonit Solvent XX400 and Vetorep ER430 should not contact the skin, eyes or be swallowed. When using, ensure adequate ventilation and avoid inhalation of vapor. Some people are sensitive to resins, hardeners, and solvents. Wear suitable protective clothing, gloves, and eye protection. The use of barrier creams provides additional skin protection. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical attention immediately. If swallowed, seek medical attention immediately. Do not induce vomiting.
Vetorep ER430 is non-flammable. Vetonit Solvent XX400 is flammable. Keep away from sources of ignition. No smoking. In the event of a fire, extinguish with CO2 or foam. Do not use a water jet.
For further information, refer to the Product Material Safety Data Sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346
Epoxy resin twin cartridge anchoring grout

">

Epoxy resin twin cartridge anchoring grout

Vetocrete FC803
High strength structural fine shotcrete

">

High strength structural fine shotcrete

Vetocrete CC806
High strength structural shotcrete

">

High strength structural shotcrete

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

Vetogrout CG513
Free-flowing pre-bagged non-shrink cementitious cable grout

">

Free-flowing pre-bagged non-shrink cementitious cable grout

view more
Featured Product
Vetonit Base WR

Weather Resistant Premix Cement Coating for Internal Use

Uses
It can be applied internally onto walls & ceiling surfaces.
On concrete surfaces that are smooth and also on precast concrete surfaces.
On wall surfaces that are plastered with water-resistant plasters, Vetonit Renders, and on damp concrete interiors.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com