Primers and Ancillary
Vetocure XT427

Water-based acrylic curing compound and primer *

Uses
As a spray-applied membrane for interior application on concrete surfaces and renders.
In situations where the surfaces need to be painted or plastered.
Fast Download
Technical Data Sheet
download (*.pdf 0.12Mb)
Method Statement
download (*.pdf 0.24Mb)
Technical Information
Product Description

Vetocure XT427 is an acrylic resin-based curing compound. When first applied to a fresh cementitious surface, the product forms a continuous non-penetrating coating. This coating dries to form a continuous film which provides a barrier to moisture loss, ensuring more efficient cement hydration, improved durability, and reduced shrinkage.

Advantages
  • Improved concrete curing enhances cement hydration and provides more durable concrete.
  • Control of moisture loss
  • Improved surface quality
  • Reduced permeability.
  • Minimized potential for surface cracking and shrinkage.
  • Compatible with many after-trade applications.
  • The easy application will reduce labor costs.
COMPLIANCE STANDARD
  • ASTM C309
  • AASHTO M148 as Type 1D
Packaging & Coverage

Vetocure XT427 is supplied in 20 & 200 liters containers.

Coverage: 4 - 6 m2/Liter

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

Shelf Life & Storage

Vetocure XT427 has a minimum shelf life of 12 months, provided the temperature is kept within the range of 5ºC to 35ºC. Avoid freezing and prolonged exposure to heat or direct sunlight. Should the temperature of the product fall outside this range, then contact Saveto Technical Service Department for advice.
Containers should be kept sealed and airtight to prevent loss of moisture by evaporation.

Colors
Milky White
Application Information
Instructions for use

Application to fresh concrete

Vetocure XT427 should be spray applied to the surface of fresh concrete. Apply approximately 30 minutes after evaporation has left the concrete free from surface water.

A spraying machine producing a fine mist may be used for Vetocure XT427 application, such as knapsack or motorized sprayers. An application trial should ensure the suitability of the machine. The spray nozzle should be held approximately 450 mm from the concrete surface and passed back and forth to ensure complete coverage. Ensure maintaining pump pressure to give an even, fine spray.

To ensure continued curing, no further application of water or other material is necessary after application. The cured surface should not be disturbed until it has sufficient strength to bear surface loads. It is recommended not to walk on the applied film before it is fully dry and ensure that it is not broken.

Application to hardened concrete

Vetocure XT427 can be applied manually if a spray machine is not available. Use a soft brush, broom, or wide roller for applying Vetocure XT427. In this situation, apply the product once the concrete has hardened sufficiently not to get damaged during application.

Vetocure XT427 may also be applied to the surface of newly hardened concrete immediately after de-molding. The surface must be structurally sound, free from oil, grease, and other forms of contamination, which may otherwise prevent the adhesion of Vetocure XT247 to the concrete.

The  recommended  coverage  rate  for  Vetocure XT427 is between 4.0 and 6.0  m2 / litrer  (0.17 - 0.25 litres/m2 ).

Over-coating and removal

Vetocure XT427 can be applied over old, covered substrates.  A small trial area is recommended to ensure that the desired properties are obtained.

Before over-coating with Vetocure XT427, ensure that the surface is completely free of stains, oils, and other materials that may interfere with the adhesion of the material.

* Important Note

Consult your Saveto technical representative for conditions and application method.

Cleaning

Clean spray equipment immediately after use by flushing through with water.

Additional Information
Health & Sefety

Vetocure XT427 does not fall into the hazard classifications of current regulations. However, it should not be swallowed or allowed to contact skin and eyes either in bulk or spray form.
Wear suitable protective gloves and goggles. Remove splashes on the skin with water. In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.
Vetocure XT427 is non - flammable.
For further information, consult the Material Safety Datasheet available for this product.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Ready Mix Bond
Multi-purpose bonding agent & admixture

">

Multi-purpose bonding agent & admixture

Saveto Bond 2
Multipurpose low viscosity bonding agent & admixture

">

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436
Polymeric soil stabilizer

">

Polymeric soil stabilizer

Vetobond PB434
Polymeric bonding agent, waterproof mix enhancer & primer

">

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433
Versatile resin adhesive, cement modifier, bonding agent & sealer

">

Versatile resin adhesive, cement modifier, bonding agent & sealer

view more
Featured Product
Cool Mortar
Advanced modified cementitious lightweight, thermal insulating masonry mortar

">

Advanced modified cementitious lightweight, thermal insulating masonry mortar

Uses
As a joint filler between lightweights and insulated blocks to obliterate thermal bridging phenomena resulting from normal mortar usage.
Use between sandwich polystyrene blocks or AAC blocks.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com