Flooring Systems
Vetodeck UD

Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system

Heavily trafficked areas.
Car park decks, car park ramps.
Turning areas, entrances, and thoroughfares.
On the new and existing floor.
Fast Download
Technical Data Sheet
download (*.pdf 0.58Mb)
Technical Information
Product Description

Vetodeck UD is a multi-layer deck protection system comprising a primer, waterproof membrane, and protective topcoat. All components are applied in the liquid phase and react chemically to form a tough, flexible, protective surface. The Vetodeck AD system is designed to provide added protection to new and existing, heavily trafficked areas.

  • Flexible and tear-resistant.
  • Multi-purpose.
  • Seamless and watertight.
  • Rapid application, reliable and safe.
  • Available in a range of standard colors.
  • UV resistant.
  • Weather-resistant.
  • Suitable for internal and external applications.
  • ASTM D412
  • ASTM D624
  • ASTM C1305
Packaging & Coverage

Vetodeck Components are supplied in:

Vetoprime EP490 is supplied in 4 & 15 liters Kit, Coverage: 7 - 10 m2/Liter.

Vetotop UC 363 is supplied in 4 & 15 liters Kit, Coverage: 1.25 m2/Liter.

Vetotop UC370 is supplied in 4 & 15 liters Kit, Coverage: 6 m2/Liter.

Vetotop UC373 is supplied in 1 & 4 liters Kit, Coverage: 70LM x 10cm/Liter.

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed kits of Vetodeck UD components have a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use


Apply Vetoprime EP490 to the prepared surface at a wet film thickness of 100 microns.



Apply Vetotop UC363 to Vetoprime EP490 surface at a wet film thickness of 750 - 900 microns. For best results, Vetotop UC363 should be applied with a notched trowel or squeegee. If Vetotop UC363 is still wet, seed with Saveto Vetograin - Grain No. 2 at a rate of 0.5kg/m2 and cure for 16 hours at 25ºC.

Top Coat:

Apply Vetotop UC370  topcoat to the membrane coat at a wet film thickness of 300 microns. The system should be permitted to cure for 72 hours @ 35°C or 7 days @ 25°C before being trafficked when the application is complete.

Line Marking:

Apply Vetotop UC373 as a line marking paint. Vetotop UC373 is available in a range of traffic RAL colors.


Clean all tools and equipment immediately after use with Vetonit Solvent.

Surface Preparation

Existing surfaces should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. All necessary repairs should be made before application by using the same material.  New concrete floors shall be at least 5 days old and visibly dry with no standing water on top.

New concrete surfaces should have reached 80% of their intended physical properties - generally only achieved after a minimum curing period of 28 days. Existing concrete surfaces must be prepared to provide a clean, sound substrate.

Additional Information
Health & Sefety

Vetodeck UD Components should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well-ventilated areas. In case of insufficient ventilation, wear suitable respiratory protection. Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection.
Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water. In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical attention immediately - do not induce vomiting.
Refer to product MSDS for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. In addition, our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetograin Range
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system


Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system

Vetotop CL530
Premixed 2 to 10 mm thick cementitious self-leveling underlayment


Premixed 2 to 10 mm thick cementitious self-leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed

Vetotop EC493
Solvent-based high performance, self-priming, thin epoxy topping


Solvent-based high performance, self-priming, thin epoxy topping

view more
Featured Product
Plaster Gypsum

High-quality gypsum plaster

Internal plaster on block walls and rough surfaces.
Plastering on fair-faced concrete and precast panels after Spatter Dash SB scratch coat.
Improving thermal resistance properties as well as sound dampening.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com