Primers and Ancillary
Ready Mix Bond

Multi-purpose bonding agent & admixture

Uses
Works as an admixture with plaster, lime/sand cement screeds, renders, mortars, and cement grouts.
Works as a bonding agent and can be sprayed or brushed on green substrates to improve bonding of plasters, patching compounds.
For renders, mortars, joint tape fixing, etc.
Use for both internal and external applications.
Fast Download
Technical Information
Product Description

Ready Mix Bond is a single component acrylic-based bonding agent for cementitious materials. It is water-based, specially formulated to enhance bonding properties and improve the mechanical strengths of plaster mixes when incorporated with mixing water. Ready Mix Bond reduces shrinkage cracks during the early stages of cement hardening by minimizing surface water loss in freshly applied mixes. Ready Mix Bond is ideal for use with a variety of sand/cement-based mixes. Ready Mix Bond can be diluted on site with potable water for desired applications.

Advantages
  • Multipurpose usage.
  • It can be used as a bonding agent & admixture.
  • Enhances bonding of plaster, sand/cement screed, renders, etc.
  • Improves hydration & curing when added to cement-based mixes.
  • Improves compression strength & abrasion.
  • It adheres well to various construction materials, including concrete, stone, etc.
  • Ensure brighter & long-lasting color to architectural finishes.
  • Reduces shrinkage & cracks.
COMPLIANCE STANDARD
  • ASTM C932
  • BS 6319
Packaging & Coverage

Ready Mix Bond is supplied in 20 liters Containers.

Coverage: 8 -10 m²/Ltr as a bonding agent.

Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Ready Mix Bond has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place below 35ºC.

Colors
Milky white liquid
Application Information
Instructions for use

Application

Ready Mix Bond tends to soft settlement on storage, and therefore it is recommended to mix the material in the same container before use.

Follow the dilution ratio required for each type of premixed mortar.

As Admixture

Add 3 parts of Ready Mix Bond with 1 part of water. Mix thoroughly to obtain uniform consistency liquid. Add the diluted Ready Mix Bond to pre-blended sand/cement plaster, mortar, or other dry mixes. Mix for 3-4 minutes using a mechanical mixer at low speed.

Let the mixture stand for 10 min and mix again briefly to achieve a homogeneous lump-free mixture.

As Bonding Agent

As a bonding agent,  Ready Mix Bond is used without dilution. Apply Ready Mix Bond using a brush or spray directly onto the substrate. If using a hand pump, spray at a rate of 8-10 m2/liter.

Immediately, while the bonding agent is still wet, follow by applying plaster, render, mortars or joint tapes, etc.

Note: Ready Mix Bond should remain tacky when applying top coat finishes.

Cleaning

Clean tools with water before it hardens. After the hardening, remove its residuals mechanically only.

Surface Preparation

Clean all surfaces and remove any dust, unsound material, plaster, oil, paint, grease, corrosion deposits, or algae. Roughen the surfaces, remove any laitance and expose aggregate by light scabbling or grit-blasting.

Limitation
  • Use the whole material once you opened the pack, as the material starts to skin & then dry. Any part material left in the container must be kept airtight.
  • Do not mix with any additives or products unless recommended by saveto.
  • For further information contact our technical department.
Additional Information
Health & Sefety

Ready Mix  Bond is irritant and harmful; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice.

Ensure adequate ventilation when using the material and avoid inhalation of vapors.

Ready Mix Bond is non-flammable.

Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Bond 2
Multipurpose low viscosity bonding agent & admixture

">

Multipurpose low viscosity bonding agent & admixture

Vetobond PB436
Polymeric soil stabilizer

">

Polymeric soil stabilizer

Vetobond PB434
Polymeric bonding agent, waterproof mix enhancer & primer

">

Polymeric bonding agent, waterproof mix enhancer & primer

Vetobond PB433
Versatile resin adhesive, cement modifier, bonding agent & sealer

">

Versatile resin adhesive, cement modifier, bonding agent & sealer

Vetobond EB431
Water dispersible epoxy bonding agent to bond old to new concrete

">

Water dispersible epoxy bonding agent to bond old to new concrete

view more
Featured Product
Vetonit Solvent XX400
Resin cleaning & thinning solvent

">

Resin cleaning & thinning solvent

Uses
Clean equipment and tools after use or mixing of epoxy-based resins.
Thinning specific epoxy products.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com