High performance, matt finish, chemical, scratch & UV resistant polyurethane floor & wall coating
Vetotop UC372 is a two-component, solvent-based polyurethane topcoat. It is used as UV resistant sealer over concrete and the range of Vetotop epoxy and polyurethane flooring & coating systems. Special additives and adhesion promoters give this material excellent penetration and adhesion to minimally profiled concrete. Vetotop UC372 is UV stable for exterior applications, cures rapidly, and the sealed system is ideal for all-weather exposure. When used as a finish coat, Vetotop UC372 gives a hard, matt finish surface that offers excellent scratch resistance and easy cleanability. Vetotop UC372 is supplied in a pack size of 4 liters kit consist of Resin & Hardener.
Vetotop UC372 is supplied in 4 Liters Kit. Theoretical Coverage 5 m2/Liter @200 WFT
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.
In the case of using antislip aggregates, the consumption values for the topcoat will increase by 15 - 20%.
The original sealed kit of Vetotop UC372 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.
Vetotop UC372 is designed to be a hard-wearing thin coat application on cementitious or metal substrates and a top coat over epoxy and aromatic urethane coatings thicknesses between 75 and 100 microns. The product is used for internal and external applications. The applied product will be resistant to water as well as a wide range of chemicals.
Mixing Vetotop UC372
In a separate mixing vessel, use a slow speed mixer to mix the base, hardener for 3 minutes. Mix these components in the quantities supplied, ensuring the containers are scraped clean. Do not add solvent thinners at any time.
Apply Vetotop UC372 by roller to the surface. The application should be at a rate of 5 m2/liter per coat.
The application should not be carried out when humidity exceeds 75% or when the surface temperature to be coated less than 3°C above the dew point.
Vetotop UC372 can be applied as a single coat or multi-coat sandwich system incorporating Vetograin products to give a slip-resistant finish.
For more information, please refer to Vetograin Technical Data Sheet.
Expansion joints in the existing substrate must be retained and continued through the Vetotop UC372 topping. Saveto has a range of joint sealants specifically designed for flooring (see Vetoflex PS782 product data sheet).
Clean tools and equipment with Vetonit Solvent XX300 immediately after use.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. Repair all necessary surfaces before application by using epoxy mortar from the Vetorep ER range.
New concrete floors shall be at least 28 days old with a moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Vetotop UC372 is irritant and harmful; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. In case of contact with eyes, clean immediately with plenty of clean cold water and seek medical advice.
Ensure adequate ventilation when using the product or when using solvent for cleaning purposes and avoid inhalation of vapors. The use of barrier creams provides additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - Do not induce vomiting.
Vetotop UC372 and Vetonit Solvent XX300 are flammable. Keep away from sources of ignition. No Smoking. In the event of a fire, extinguish with CO₂ or foam. Refer to product(s) MSDS for further information.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system
Premixed 2 to 10 mm thick cementitious self-leveling underlayment
Premixed 10 to 30 mm thick cementitious screed
Premixed 30 to 100 mm thick cementitious screed
Silicone-based polymeric water repellant pore sealer & hardener for limestone, masonry & natural stone