Protective Coatings
Vetotouch Sealer

Decorative protective sealer for cementitious finishes

(Formally known as Vetotop AC444)  

Uses
Sealing of Vetotouch range of cementitious decorative products.
Semi-Solid finish protection and sealing of cementitious facades.
Fast Download
Technical Data Sheet
download (*.pdf 0.08Mb)
Method Statement
download (*.pdf 0.23Mb)
Technical Information
Product Description

Vetotouch Sealer is an environmentally friendly polymeric pore sealer for the decorative products of the Saveto Vetotouch range. The product seals the surface finish to protect against contaminants and water ingress.

Advantages
  • Easily applied by the roll or airless spray.
  • Protects against contaminants and water ingress.
  • Designed to work with cementitious finishes and Vetotouch range of products.
  • Cost effective, suitable for use in MENA region weathering conditions.
Packaging & Coverage

Vetotouch Sealer is supplied in 20 liters container.

Theoretical coverage: 3 - 6 m2/ liter/ coat.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

 

Shelf Life & Storage

The original sealed container of Vetotouch Sealer has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.

Colors
Colored Liquid
Application Information
Instructions for use

Design Criteria

Designed to work with Vetotouch range of cementitious decorative products. The application is designed to 2 - 3 coats at a rate of 3 to 6 m2 per liter per coat to achieve the best results and closing the substrate surface. The coverage rate may decrease or increase depending on the porosity of the substrate and its texture.

Note: You can dilute by water up to 15% if required.

Application

Apply Vetotouch Sealer as a continuous flood coat using either a soft brush or low-pressure spray equipment at the correct coverage rate. For best performance, apply a flood of 2 - 3 coats at a rate of 3 - 6 m2 per liter per coat.

Cleaning

Clean equipment and tools using clean water immediately after use. If residual material exists or hardens, mechanical means such as wire brush would be required to remove residue.

 

Surface Preparation

The surface must be sound and thoroughly clean by compressed air before applying Vetotouch Sealer.

Additional Information
Health & Sefety

Vetotouch Sealer should not come into contact with skin and eyes or be swallowed. Avoid inhalation of vapor and spray. Use only in well-ventilated areas. In case of insufficient ventilation, wear suitable respiratory protection.

Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection.

Should accidental skin contact occur, remove immediately with a suitable skin cleanser followed by washing with soap and water.

In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.

If swallowed, seek medical attention immediately - do not induce vomiting.

Refer to Material Safety Data Sheet for further information.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof EC720

Non-toxic solvent-free epoxy waterproof wall, floor & tank coating

Vetoproof EC760

Two-component coal tar solvent epoxy protective coating

Vetoproof EC761

Solvent-free coal tar epoxy-based protective coating

Vetoproof EC722

Epoxy Polysulphide Elastomeric Coating System

Vetoseal XW770
Silicone-based polymeric water repellant pore sealer & hardener for limestone, masonry & natural stone

">

Silicone-based polymeric water repellant pore sealer & hardener for limestone, masonry & natural stone

view more
Featured Product
Vetotouch Monocouche

UV resistant pigmented premixed textured plaster

Uses
Internally or externally in wet & dry conditions onto block walls & rough surfaces.
On concrete surfaces that are smooth and also precast concrete surfaces with scratch coat applied first.
It can be applied up to 20mm thickness of the single-layer; however, it is recommended for two coat applications of 10mm each.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com