Self smoothening epoxy-based floor topping from 3 to 5 mm thickness
Vetotop EL699 is a multi-component high-performance self smoothening epoxy flooring system that flows in a light oil-like manner to self smoothen to a perfect level. Once cured, the product has excellent abrasion and chemical resistance. Vetotop EL699 provides an attractive, hard-wearing, and easily cleanable floor finish. Its use on floors will enhance the lighting in the environment due to the product's reflective properties.
BS EN476:2009 as class 1 in flame spread.
Vetotop EL699 is supplied in 15 Liters Kit, Theoretical Yield: 5 m²/kit @ 3mm thickness.
Vetoprime EP691 is supplied in 4 Liters Kit, Theoretical Yield: 7-10 m2/ Liter.
Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.
The original sealed kit of Vetotop EL699 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.
Vetotop EL699 is designed to be a hard-wearing self smoothening single pour application on cementitious substrates at thicknesses between 3 to 5mm. The applied product will be resistant to water as well as a wide range of chemicals.
All surfaces receiving Vetotop EL699 should be primed with Vetoprime EP691, designed for maximum absorption and adhesion to concrete substrates. Add the entire content of the hardener tin to the base tin and mix the two primer components thoroughly for at least 2 minutes - only mix full packs. Once mixed, apply the primer immediately to the prepared substrate using stiff brushes and/or rollers. The primer should be well ‘scrubbed’ into the substrate to ensure full coverage, take care to avoid over-application or ‘ponding.’ Allow the primer to dry before proceeding to the next stage, do not proceed whilst the primer is ‘tacky’ as this will lead to unsightly marks in the finished surface. Porous substrates may require a second primer coat - when the first coat is directly absorbed into the substrate - but observe minimum over-coating time.
Vetotop EL699 is supplied in three pre-weighed packs (base, hardener, and aggregate), ready for immediate on-site use. Part mixing of these components is not acceptable and will affect both the performance and appearance of the finished floor. Mixing should be carried out using either a forced action mixer; or a heavy-duty mobile mixer fitted with a jiffy type mixing paddle. All such equipment should be of a type and capacity approved by Saveto. The components should be mixed in a suitably sized mixing vessel. Stir the base and hardener components individually, then empty them into the mixing vessel scrapping the edges and mix for 2 minutes. The contents of the graded aggregate pack should be slowly added and mixing carried out for a further 3 minutes until obtaining a completely homogeneous material.
Ensure sufficient labor and materials to make the mixing and subsequent application process a continuous one for any given, independent floor area. Once mixed, pour the material immediately on the floor and spread before aggregate settlement occurs. Pour the material onto the prepared and primed substrate as soon as mixing is complete. Spread to the required thickness using a notched trowel or a gauged spreader, with care taken not to overwork the resin, spreading evenly and slowly. After laying, roll the material immediately, using a spiked nylon roller to remove slight trowel marks and assist air release. Use a ‘back and forth’ technique along the same path for rolling. An overlap of 50% with adjacent paths is recommended. Further light rolling may be required to remove surface imperfections or for subsequent release of trapped air but should be before the setting of the product.
Follow all existing expansion or movement joints through the new floor surface.
Remove Vetoprime EP691 and Vetotop EL699 from tools and equipment with Vetonit Solvent XX600 immediately after use. Remove Hardened material mechanically.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. Repair all necessary before application by using epoxy mortar from the Vetorep ER range. New concrete floors shall be at least 28 days old with a moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).
Vetotop EL699 is non flammable. Refer to the product material safety data sheet for information.
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Polyurethane based heavy-duty, waterproof, and UV resistant car park decking system
Hard-wearing silica aggregates to be used in conjunction of Saveto anti-slip flooring system
Premixed 2 to 10 mm thick cementitious self-leveling underlayment
Premixed 10 to 30 mm thick cementitious screed
Premixed 30 to 100 mm thick cementitious screed
Professional grade cementitious non sanded tile grout