Renders & Finishes
Vetogyps Compound

Gypsum surfaces skim and finish compound

Suitable for use as a skim coat for dry gypsum surfaces and gypsum board surfaces.
Suitable for coating gypsum board angles and fastener heads when used in conjunction with Vetonit Gypsum Joint Compound.
Internally onto the horizontal & vertical dry gypsum surfaces and gypsum board surfaces.
Fast Download
Technical Data Sheet
download (*.pdf 0.26Mb)
Technical Information
Product Description

Vetogyps Compound is supplied as putty in pre-weighed pails ready to use on-site. Vetogyps Compound is a high-quality air-drying compound suitable for skim coat applications. It is ideal as a finishing coat for all gypsum surfaces,  gypsum board surfaces, angles, and fastener heads.

Vetogyps Compound complies with ASTM C475.

  • Factory controlled pre-blend ensures consistently high quality.
  • Ready to use and easy to apply, with minimal mixing and cleaning of tools.
  • Premium grade, all-purpose or finishing compound.
  • Used as a skim coat.
  • Excellent workability, easy application by hand or with mechanical tools.
  • It can be sanded by hand or with mechanical sanding tools.
  • Excellent surface for painting.
  • ASTM C475
Packaging & Coverage

Vetogyps Compound is supplied in 28kg Plastic Pails.

Coverage of 50 - 70m2/28kg (depends on the substrate).

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed container of Vetogyps Compound has a shelf life of 12 months, provided it is stored in a dry shaded place at room temperature. Protect from freezing, exposure to extreme heat, and direct sunlight.

Application Information
Instructions for use

Product Preparation

Keep Vetogyps Compound containers at room temperature for 24 hours before use. Use directly from the container. Stir contents lightly if needed. 


Apply Vetogyps Compound over dry gypsum surfaces and gypsum board surfaces either manually or by spray machine. When using Vetogyps Compound for skim coating, work the mixed material to a smooth level using a putty knife. Allow each coat to dry completely before recoating and sanding. Sand Vetogyps Compound surface with care using grit paper. The final coat should be applied to a smooth finish.

Finishing Inside Corners

Apply compound to both corner sides using a putty knife. Fold tape along the center crease. Press into position. Embed tape with a putty knife. Remove excess compound and apply a thin coat over the tape. Let dry and apply a second coat on one side. Let dry and then cover the other side. When dry, sponge smooth if necessary.

Finishing Outside Corners

Fasten metal corner bead. Apply three coats of Vetogyps Compound and allow to dry between coats; smooth the surface with a wet sponge, if necessary. Extend the first coat onto the gypsum panel using a suitable putty knife.


Vetogyps Compound is self-curing and does not require water treatment.


Clean all tools should immediately after finishing with water. Clean hardened materials mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, etc.

Allow wet surfaces to dry completely before the putty application.

Product Preparation

Keep Vetogyps Compound containers at room temperature for 24 hours before application. Use directly from the container. Stir contents lightly if needed. 

  • It is not recommended to apply Vetogyps Compound at interior temperatures less than 100C. Under cold or wet weather conditions.
  • Do not apply Vetogyps Compound over surfaces or joints that are not thoroughly dry; pinholes may result.
  • The inclusion of the other materials to a mix will impair the performance (e.g., reduced strength and poor adhesion) and void the product warranty.
  • Consume an opened pail within 48 hours.
Additional Information
Health & Sefety

Avoid direct contact of Vetogyps Compound with eyes or skin. It is recommended to use protective gloves, approved disposable respirators, and goggles during application. Any skin contact should be washed with soap and water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Dust from this product contains silica. Prolong inhalation may be harmful to health. Ensure adequate ventilation. Do not swallow the contents of the package. If ingested, seek medical advice immediately.

Keep contents out of children's reach.

Vetogyps Compound is non-flammable.

For further information, please refer to Vetogyps Compound  Material Safety Data Sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Saveto Putty Fine

PVA copolymer based high-quality putty

Vetonit Crack Filler

High quality premixed surface crack filler

Vetonit Finish WR

Water resistant internal use premix smooth cement coating

Vetonit Finish WR EG

Water-resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

view more
Featured Product
Vetotherm Flex
Cementitious based adhesive and base coat for EIFS / ETICS


Cementitious based adhesive and base coat for EIFS / ETICS

Expanded and extruded polystyrene and rock wool adhesive on cementitious substrates, masonry, and gypsum boards.
Fiber mesh reinforced base coat as part of EIFS / ETICS systems.
Ready to receive a wide range of decorative finishes.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718