Plasters & Masonry
Vetostone Filler

Colored premixed cementitious joint filler between walls and floors for stone constructions

Uses
Use internally or externally in wet & dry conditions.
Use for heritage and primitive stone wall constructions.
Fast Download
Technical Data Sheet
download (*.pdf 0.10Mb)
Technical Information
Product Description

Vetostone Filler is a cement-based blend composed of hydraulic binders, selected aggregates, and high-performance additives. It is supplied as a dry powder in pre-weighed bags ready to use on-site, which requires only the addition of clean water to produce cohesive filling mortar. Vetostone Filler is a premium quality product that contains a special adhesion additive. Vetostone Filler can be applied in joints from 5mm to 50mm.

Advantages

Factory controlled pre-blend ensures consistently high quality.

Requires only the addition of water on-site at the time of usage.

Suitable for ME harsh weather conditions.

Strong adhesion on a variety of stones.

Strong bond.

Internal & external applications.

Suitable for wet to dry conditions.

Available in Vetonit Standard Colors.

COMPLIANCE STANDARD

ASTM C270 & C780

BSEN 998-2, Type G

Packaging & Coverage

Vetostone Filler is supplied in 50kg Bag.

Yield ≈ 29 – 31 lit wet/50kg dry.

Stated consumption data are for general guidance. Actual consumption depends on the nature of the substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed bag of Vetostone Filler has a shelf life of 12 months, provided it is stored clear of ground in a dry, shaded place, at temperatures between 5ºC - 35ºC.

Colors
Coloured Powder
Application Information
Instructions for use

Mixing

Add to the mixing container 9 - 11 liters of water for each 50kg bag of Vetostone Filler. Add the powder to the water and mix for 3-4 minutes using a mechanical plaster mixer or a low-speed electric drill fitted with a suitable paddle until achieving a uniform, colored lump-free consistency.

Blend Vetostone Filler manually for small quantities and maintain the correct amount of powder to water. Mix for approximately 1-2 minutes until achieving a homogeneous mix.

Application

Neutralize the suction of the joint and stone with water before applying the mortar. Remove any excess water.

Use Vetostone Filler to fill the joints between the stones vertically and horizontally using a mason spatula/ trowel.

After stiffening, give Vetostone Filler a final smoothing to remove protrusions and to eliminate undulations.

Cleaning

Clean all tools immediately after finishing with water. Clean hardened materials mechanically.

Surface Preparation

Joint Preparation

The joint should be sound, clean, free from loose material, grease, laitance, dirt, curing compound, etc.

Before Vetostone Filler application, neutralize the stone and joint suction with clean potable water.

Additional Information
Health & Sefety

Vetostone Filler is highly alkaline; therefore, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eye irritation, immediately wash with a copious amount of clean cold water. Seek medical advice.

Vetostone Filler is non-flammable.

For further information, please refer to the material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Acoustic Plaster

High-quality lightweight premixed acoustic plaster

Masonry Grout Filler

Premixed cementitious masonry grout

Plaster Cement Perlite
Sprayable lightweight premixed plaster

">

Sprayable lightweight premixed plaster

Plaster Gypsum

High-quality gypsum plaster

Plaster Gypsum Perlite

Light weight gypsum perlite plaster

view more
Featured Product
Vetoproof UM765

Pitch-modified elastomeric polyurethane liquid applied waterproofing membrane

Uses
Wet areas: kitchens, bathrooms, swimming pools,...etc.
Basements, tunnels, subways, and culverts.
Inverted roofs, suspended slabs, balconies.
Tanking systems.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com