Concrete Repairs & Grouts
Vetocrete CC806

High strength structural shotcrete

Uses
It is ideal for large vertical and overhead structural repairs.
It is used for supporting columns and beams.
It is ideal for new construction projects.
Fast Download
Technical Data Sheet
download (*.pdf 0.09Mb)
Method Statement
download (*.pdf 0.38Mb)
Technical Information
Product Description

Vetocrete CC806 is a single component polymer modified fibered cementitious structural repair fine shotcrete product applied pneumatically, ready to use, and only requires the addition of water on site. Once mixed, the product becomes a pumpable, sprayable fine concrete suitable for structural repair while being compatible with most concrete. Vetocrete CC806 is composed of a blend of hydraulic cement, carefully selected and graded aggregates, fibers, and special additives to give it its unique properties.

Advantages
  • Easy to use, a single component product.
  • High physical and mechanical properties.
  • Extremely low permeability where it provides reinforcement protection against corrosion and resistance to ingress of contaminants.
  • Non-Shrink properties ensure dimensional repair stability.
  • Suitable for internal and external applications.
  • It is breathable and compatible with host concrete.
  • Thixotropic properties allow a high build-up in vertical and overhead repairs.
  • Very low sag.
COMPLIANCE STANDARD
  • ACI 506
Packaging & Coverage

Vetocrete FC803 is supplied in a 50kg bag.

Yield: 23 Liters.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed bag of Vetocrete CC806 has a shelf life of 12 months, provided it is stored clear of the ground, in a dry and shaded temperature-controlled place, at temperatures between 5-35 ºC.

Application Information
Instructions for use

Mixing

To ensure proper mixing, use a mechanically powered mixer or a drill fitted with a suitable paddle. Add 5.5-6.75 liters of clean water to a clean container. Then slowly add the powder to the water while mixing continuously with a low-speed mixer/drill (400-600 rpm). Continue mixing for 5 minutes until obtaining a uniform consistency.

For large quantities, use a large mechanical drum mixer. Add water to fill 2/3 of the mixer capacity. While mixing, add the powder and follow it by gradually adding the rest of the water until reaching the desired consistency.

Placing and Finishing

Apply Vetocrete CC806 pneumatically using a suitable pump to ensure good adhesion with the steel reinforcements and the substrate. Initially, Finish and level the surface by using an aluminum rod or steel trowel. Use steel float for the final finishing.

Finish the applied material surface within two hours, as the material sets faster than regular concretes and mortar.

Curing

Vetocrete CC806 is a cementitious-based material; therefore, cure it similarly to concrete by continuous watering and covering the surface with polyethylene sheets.

Cleaning

Clean all tools immediately after application by using freshwater. Clean hardened materials mechanically.

Surface Preparation

Surface Preparation

Cut back all damaged and weak concrete to reach sound concrete and/or to a minimum depth of at least 10mm.

Grit blasted corroded steel reinforcement to remove all rust traces. In case of significant loss in the steel reinforcement cross-section, replace the steel. Remove all concrete forms around the exposed steel reinforcements to a thickness of 25mm. Saw cut the perimeters of the repair area to a minimum depth of 10mm. Clean the prepared area thoroughly by using a brush and/or compressed air.

For new construction, prepare a steel reinforcement and pump the material until reaching the desired thickness. Use a suitable high to medium pressure pneumatic pump.

Priming

In repair work, and to accept Vetocrete CC806, prime all grit blasted steel reinforcements within 2 to 4 hours of application by applying one or two coats of corrosion inhibitor for steel reinforcement Vetoprime CP436.

Soak the areas to be repaired with Vetocrete CC806 with clean water before applying the repair mortar. Remove all excess water before the application, and apply one coat of acrylic bonding agent Vetobond AB432.

Allow Vetobond AB432 to become tacky before applying the repair mortar Vetocrete CC806.

For new construction, clean the substrate and steel reinforcement from dirt, rust, or anti-adhering materials.

Limitation

Apply Vetocrete CC806 in a single application for sections up to 20mm thick in overhead applications

Additional Information
Health & Sefety

Vetocrete CC806 contains reins, which may cause sensitization by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves, and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin-removing cream, followed by soap and water. Do not use solvent. In case of contact with the eye, rinse immediately with plenty of clean water, and seek medical advice. If swallowed, seek medical attention immediately. Do not induce vomiting. Vetocrete CC806 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical datasheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoanchor EG346
Epoxy resin twin cartridge anchoring grout

">

Epoxy resin twin cartridge anchoring grout

Vetocrete FC803
High strength structural fine shotcrete

">

High strength structural fine shotcrete

Vetogrout CG510

Multipurpose universal cementitious non-shrink grout

Vetogrout CG513
Free-flowing pre-bagged non-shrink cementitious cable grout

">

Free-flowing pre-bagged non-shrink cementitious cable grout

Vetogrout CG518
Chloride free nonmetallic non-shrink grout

">

Chloride free nonmetallic non-shrink grout

view more
Featured Product
Vetoflex PBR

Closed-cell polyethylene backing rod

Uses
Controlling and filling gaps behind sealants.
Prohibiting sealant bonding to joint fillers.
Allowing joint sealant freedom of movement to achieve its desired function.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com