Protective Coatings
Vetoproof EC761

Solvent-free coal tar epoxy-based protective coating

Uses
Protection of Seawater tanks, channels, and intakes.
Pipe and manhole lining.
Sewage works and effluent plants.
Foundation waterproofing, Jetties, piers, and docks.
Fast Download
Technical Information
Product Description

Vetoproof EC761 is a two-component solvent-free tar extended epoxy coating system that adheres perfectly to concrete and metal substrates. Once cured, the product has excellent abrasion and chemical resistance. Vetoproof EC761 provides a hard-wearing and easily cleanable protective coating. Its use on floors, walls, structural elements, and tanks to protect against ingress of contaminants.

Advantages
  • Versatile use.
  • Does not support algae or bacterial growth.
  • Excellent chemical resistance.
  • Enhances structural life expectancy.
  • Primerless.
  • Protects reinforcement steel and metal substrates against corrosion.
Packaging & Coverage

Vetoproof EC761 is supplied in 18 Liters Kit.
Theoretical Coverage: 5 m²/liter / coat @ 200 microns.

Stated consumption data are for general guidance. Actual consumption depends on the nature of substrate, method of application, and wastage.

Shelf Life & Storage

The original sealed kit of Vetoproof EC761 has a shelf life of 12 months, provided it is stored clear of ground in a dry and shaded place below 35ºC.

Application Information
Instructions for use

Mixing

Thoroughly stir the individual components of  Vetoproof EC761 before the two are mixed. Pour the entire contents of the hardener container into the base container and mix the material thoroughly for at least 3 minutes. The use of a heavy-duty slow speed, flameproof, or air-driven drill fitted with a mixing paddle is desirable.

Application

Apply the mixed Vetoproof EC761 to the prepared surface using a brush or lambs-wool roller. Ensure that the area is completely coated.

Curing

Allow the applied to cure for 7 days to achieve full cure to receive its chemical resistance properties.

Cleaning

Remove Vetoproof EC761 from tools and equipment with Vetonit Solvent XX400 immediately after use. Remove hardened material mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.

Laitance and weak surface layer shall be removed using mechanical methods such as grinding or blasting to provide a sound, well-profiled surface. Repair all necessary repairs before application by using epoxy mortar from the Vetorep ER range. Pinholes, blowholes, and minor irregularities can be leveled and filled by Vetorep ER350.

New concrete floors shall be at least 28 days old with a moisture content of less than 5% (shall earlier application be required testing of substrate for moisture conditions shall be made).

Blast grit steel substrates to surface quality SA2½ (BS 4232:Second Quality), and application shall occur within 2 to 4 hours after blasting.

Additional Information
Health & Sefety

Vetoproof EC761 and Vetonit Solvent XX400 should not come into contact with skin and eyes or be swallowed. Ensure adequate ventilation and avoid inhalation of vapors. Some people are sensitive to resins, hardeners, and solvents. Wear suitable protective clothing, gloves, and eye protection. If working in confined areas, use suitable respiratory protective equipment.

The use of barrier creams provides additional skin protection. In case of skin contact, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately - Do not induce vomiting.

Vetoproof EC761 is non-flammable.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any liability, either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right to change any of the technical data sheets' specifications upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetoproof EC720

Non-toxic solvent-free epoxy waterproof wall, floor & tank coating

Vetoproof EC760

Two-component coal tar solvent epoxy protective coating

Vetoproof EC722

Epoxy Polysulphide Elastomeric Coating System

Vetoseal XW770
Silicone-based polymeric water repellant pore sealer & hardener for limestone, masonry & natural stone

">

Silicone-based polymeric water repellant pore sealer & hardener for limestone, masonry & natural stone

Vetoseal XX777
Silane acrylate surface treatment, enhancer, and hardener for limestone, concrete, and masonry

">

Silane acrylate surface treatment, enhancer, and hardener for limestone, concrete, and masonry

view more
Featured Product
Vetonit Thick Render

Water Resistant Thick Patch & Repair Premixed Render

Uses
Internal & external plaster on block walls and rough surfaces.
Applied on both vertical and overhead surfaces.
On concrete surfaces that are smooth and also precast concrete surfaces with scratch coat applied first.
Plastering to a thickness of 15 mm in a single application.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com